instructions for
AIR PAlm oRbItAl sAndeR Ø75mm
model no:
GsA003
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. sAfety
WARnInG!
ensure that Health & safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
WARnInG!
disconnect from air supply and before changing accessories, servicing or maintenance.
9
maintain the sander in good condition (use an authorised service agent).
9
replace or repair damaged parts. use recommended parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9
use the sander in a suitable work area. Keep area clean, tidy and free from unrelated materials. ensure that there is adequate lighting.
9
Before each use check abrasive pad for condition. if worn or damaged replace immediately.
9
ensure that there are no flammable or combustible materials near the work area.
WARnInG!
Always wear approved PPe protection when operating the sander.
9
if dust is generated, use face, dust, or respiratory protection in accordance with cosHH regulations.
9
depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
9
remove ill fitting clothing. remove ties, watches, rings and loose jewellery. contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
maintain correct balance and footing. ensure that the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
check moving parts alignment on a regular basis.
9
ensure that the work piece is correctly secured before operating the sander. never hold a work piece by hand.
9
check the work piece to ensure that there are no protruding nails, screws, stones, etc.
9
Avoid unintentional starting.
WARnInG!
ensure that the correct air pressure is maintained and not exceeded.
9
Keep air hose away from heat, oil and sharp edges. check air hose for wear before each use and ensure that all connections are
secure.
9
Prolonged exposure to vibration from these tools poses a health risk. it is the owner’s responsibility to correctly assess the potential hazard,
issue guidelines for safe periods of use and offer suitable protective equipment.
8
do not
use the sander for a task it is not designed to perform.
8
do not
operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
WARnInG! do not
cut, grind, saw or sand any materials containing asbestos.
8
do not
carry the sander by the hose, or pull the hose from the air supply.
8
do not
get the sander wet or use in damp or wet locations. these models are dry sanders only.
8
do not
operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do not
use sander where there are flammable liquids, solids or gases, such as paint solvents and including waste wiping or cleaning
rags etc.
8
do not
leave the sander operating unattended.
8
do not
carry the sander with your finger on the power lever.
8
do not
direct air from the air hose at yourself or others.
9
When not in use disconnect from air supply, and store in a safe, dry, childproof location.
leAd PAInt WARnInG!
Paint once contained lead as a traditional ingredient. contact with the toxic dust from the removal of such paint must therefore be
avoided. the following action must be taken before using the sander on a surface that you suspect may contain lead paint.
1.
user must determine potential hazard relating to age of paint to be removed (modern paints do not have lead content).
2.
dAnGeR!
Keep all persons and pets away from the work area. the following are particularly vulnerable to the effects of lead
paint dust: Pregnant women, babies and children.
3. We recommend personal protection by using the following safety items:
a) Paint spray respirators.
b) Pe coated Hooded coverall.
c) latex Gloves.
4. take adequate measures to contain the paint dust, flakes and scrapings.
5.
continue to wear safety equipment whilst thoroughly clean all areas when task is complete.
6. seal paint waste in bags or containers for disposal according to local regulations.
GsA003 | issue 1 09/01/17
Original Language Version
© Jack sealey limited
refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear a mask
