INSTRUCTIONS FOR:
RADIAL PILLAR DRILLS
MODEL No’s:
GDM790BR & GDM1630FR
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
GDM790BR,GDM1630FR Issue; 6(S) - 07/02/18
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear safety
footwear
Wear a mask Indoor use only
1.1.
ELECTRICAL SAFETY
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer. If the product is used in the course of business duties, it
must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.1.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.2.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
replaced immediately by a qualified electrician.
1.1.3.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
B) Connect the BROWN live wire to the live terminal ‘L’.
C) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
p
WARNING! Disconnect drill from mains power before changing accessories, servicing or performing any maintenance.
3
Maintain the
drill in good condition (use an authorised service agent).
p
WARNING!
Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts.
A guard or any other part that is damaged must be repaired or replaced before the tool is next used, to ensure that it will
operate properly and perform its intended function. The safety guard is a mandatory fitting where drill is used in premises
covered by the Health & Safety at Work Act.
3
Check alignment of moving parts and check for possible broken parts.
3
Replace or repair damaged parts.
Use genuine Sealey parts only. Non-authorised parts may be dangerous and will invalidate the
warranty.
3
Ensure the set screws of the head frame are screwed tight before using the drill.
3
Secure the drill to the bench/floor to avoid the machine tipping, sliding or walking. Drill is designed for use with drill bits only. No other
accessory may be used.
3
Ensure the chuck is securely fastened to the spindle.
3
Remove adjusting keys and wrenches from the machine and working area before switching on.
3
Use clamps or a vice (not included) to secure the workpiece. Available from your Sealey stockist.
DO NOT
secure the workpiece by
hand.
3
Refer to speed chart for recommended drilling speeds.
p
WARNING! Always wear approved eye or face protection when operating this drill. Use a dust mask if dust is generated.
p
WARNING! DO NOT wear gloves when drilling.
3
Others in the workplace should be kept at a safe distance from the drill, especially when it is in operation.
3
Keep the work area as childproof as possible by using padlocks and master switches.
3
Keep drill bits clean and sharp for best and safest performance.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Locate the drill in a suitable work area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Avoid unintentional starting.
7
DO NOT
use drill for a task it is not designed to perform.
7
DO NOT
allow untrained persons to operate the drill.
Replacement fuse rating:
13A
