3
Others in the workplace should keep a safe distance from the drill, especially when it is in operation.
3
Keep the work area as childproof as possible by using padlocks and master switches.
3
Keep drill bits clean and sharp for best and safest performance. Follow the instructions for lubrication and changing accessories.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Locate the drill in a suitable working area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Secure non-stable work piece with a clamp, vice or other adequate holding device.
3
Avoid unintentional starting.
7
DO NOT
use the drill for a task it is not designed to perform.
7
DO NOT
allow untrained persons to operate the drill.
7
DO NOT
get the drill wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT
operate the drill if damaged.
7
DO NOT
use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away from
the drill when operating. Flammable waste, such as wipes or cleaning rags, must be placed in a closed metal container and disposed of
correctly.
7
DO NOT
exceed the rated capacity of the drill.
7
DO NOT
operate the drill if any parts are missing as this may cause failure or personal injury.
7
DO NOT
leave the drill operating unattended.
7
DO NOT
operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT
pull the cable from the power supply.
3
When not in use switch the drill off, remove plug from the power supply and do not leave until the tool has come to a complete stop.
3. TECHNiCal SpECiFiCaTiON
2. DESCripTiON
The GDM50B 5 speed bench drill is suitable for light industrial, agricultural and woodworking applications. The drill is fitted with a flip-up safety
guard and “No Volt Release” switch which prevents accidental restart after a mains power interruption. A rack and pinion feed shaft with preset depth
control for repetitive work is also included. Work clamps are also available for this drill, contact your local Sealey dealer for information.
4. CONTENT
4.1. package content
Unpack the parts listed below and check to ensure they are in good condition. Any queries must be reported to your dealer immediately.
3
Head Assembly
3
Base
3
Chuck and Key
3
Column with Flange
3
Feed Handles and Knobs (3)
3
Table Arm, Bracket and Worm
3
Adjusting Handle with Set Screw (table)
3
Table
3
Rack and Rack Ring
3
Pivoted Clamp Bolts (2 - table arm & bracket)
3
Bolts and Washers (4)
3
Screw (upper pulley cover)
3
Safety Guard
3
Arbor
3
Set Screws (2)
3
Wedge
3
Hex. Keys (2)
MODEl No:
GDM50B/GDM50BX
Drilling Capacity (Chuck Size):
16mm
Spindle Nose Taper:
MT2
Swing:
314mm
Spindle centre to column:
127mm
Spindle travel:
60mm
Number of speeds:
5
Speed range:
460-2890rpm
Maximum Distance Spindle to Table:
275mm
Maximum Distance Spindle to Base:
385mm
Working Table Surface size:
Ø250mm
Working Base Surface size:
155 x 165mm
Overall Base Size:
340 x 210mm
Column diameter:
60mm
Collar diameter:
55mm
Overall Height:
745mm
Motor power:
220W - 230V
input power:
370W - 230V
Weight:
35kg
Optional Keyless Chuck 16mm:
GDMX/KC
Original Language Version
GDM50B (GDM50BX) Issue: 3 - 05/03/12
