5. TRANSPORTATION AND STORAGE
!
WARNING! Petrol is highly flammable and petrol vapour is explosive. Do not permit smoking, naked flames, sparks or heat in
the vicinity while handling petrol. Avoid spilling petrol onto a hot engine. Comply with all laws regulating storage and handling
of fuels.
5.1
TRANSPORTATION
5.1.1 Do not overfill the fuel tank.
5.2.2 Do not operate the generator whilst it is on a vehicle. Remove it from the vehicle and operate it in a well-ventilated place.
5.2.3 To prevent fuel spillage during transportation, it should be secured in its normal, upright position with the engine switch to OFF.
5.2
STORAGE
5.2.1 Prior to storing the generator for a prolonged period, ensure that the storage area is free of excessive humidity and dust.
5.2.2 Completely drain the fuel from the tank into an approved container.
6. TROUBLESHOOTING
PROBLEM
CAUSE
ACTION
Engine will not start.
No fuel in tank.
Fill fuel tank.
Oil not filled to correct level.
Fill oil to correct level.
Engine run switch not turned on.
Set engine control correctly.
Choke not set correctly.
Set choke control correctly.
Spark plug fouled.
Clean/replace spark plug.
Air cleaner blocked.
Clean/replace air filter.
Engine does not run
Air cleaner blocked.
Clean/replace air filter.
smoothly.
Spark plug fouled.
Clean/replace spark plug.
Choke set incorrectly.
Set choke control correctly.
Dirty or stale fuel.
Drain and replace fuel.
Declaration of Conformity
We, the sole importer into the UK, declare that the product listed here is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a national authority, upon
request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products.
Signed by Steve Buckle
22nd August 2006
GENERATOR 1000W 230V
Model: G1000E.V2
98/37/EC Machinery Directive
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
93/68/EEC Marking Directive
G1000E.V2 - 1 - 220806
7. DECLARATION OF CONFORMITY
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
4.3
SPARK PLUG CLEANING
Every 100 hours.
4.3.1 Remove the top maintenance cover by pushing in the side and lifting away (fig.11).
4.3.2 Remove the spark plug cap and clean away any dirt etc. from the spark plug area.
4.3.3 Use the wrench provided to remove the spark plug (fig.11).
4.3.4 Inspect the spark plug, renew if the insulator is cracked. Carefully clean the spark plug with a wire brush if it is to be reused.
4.3.5 Check the plug gap with a feeler gauge, the gap should be between 0.6-0.7mm (0.024-0.028in). Adjust if necessary by carefully bending
the electrode.
4.3.6 Install spark plug by hand initially, to avoid cross-threading. Finally tighten with the wrench (1/2 turn for a new spark plug and 1/8-1/4
turn for a used one).
4.3.7 Reconnect spark plug cap and replace the top maintenance cover.
fig.11
fig.10
