![background image](http://html.mh-extra.com/html/sealey/ecs400/ecs400_instructions-manual_1224399001.webp)
ElEctronic chargEr startEr12/24V
400amp max
model no:
Ecs400
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safEty
1.1.
Electrical safety
Warning!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
9
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also
recommend that a Residual Current device (RCd) is used. It is particularly important to use an RCd with portable products that are
plugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a
Residual Current device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
9
The electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
9
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe
condition of those appliances and the safety of the appliance operators.
If in any doubt about electrical safety, contact a qualified electrician.
9
ensure that the insulation on all cables and on the appliance is safe before connecting it to the
power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester.
9
ensure that cables are always protected against short circuit and overload.
9
Regularly inspect power supply leads and plugs for wear and damage and power connections to
ensure that none is loose or damaged.
9
ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
8
Do not
pull or carry the appliance by the power cable.
8
Do not
pull the plug from the socket by the cable.
8
Do not
use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician.
8
This product requires an electrical supply in excess of 13 amp, and no plug is fitted. You must
therefore contact a qualified electrician to ensure that a 16 amp supply is available. We recommend
that you discuss the installation of a industrial round pin plug and socket with your electrician.
ensure that the unit is correctly earthed via a three-pin plug, as shown.
a) Connect the gReen/YelloW earth wire to the earth terminal .
b) Connect the BRoWn live wire to live terminal ‘l’.
c) Connect the Blue neutral wire to the neutral terminal, ‘n’ or unmarked.
d)
After wiring, check that there are no bare wires, that all wires have been correctly connected,
that the external insulation extends beyond the cable restraint and that the restraint is tight.
9
If an extension reel is used it should be fully unwound before connection. A reel with an RCd fitted
is preferred since any appliance plugged into it will be protected. The cable core section is important
and should be at least 1.5mm
²
, but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may
be used in the other output sockets, we recommend the use of 2.5mm
²
section cable.
Warning!
modern vehicles contain extensive electronic systems.
You are required to check with the vehicle Manufacturer, for any specific instructions regarding the use of this type of equipment on
each vehicle. no liability will be accepted for damage / injury, where this product is not used in accordance with all instructions.
eCS400 | Issue 2 (H13F) 20/04/18
Original Language Version
© Jack Sealey limited
Refer to
instructions
electrical
shock
hazard
Wear eye
protection
Wear protective
gloves
Warning
corrosive
substance
Warning:
explosive
material
Keep away
from sources of
ignition
use in well
ventilated areas
Keep in dry area
protect from rain
it is rEcommEnDED that
thE sUpply to this proDUct
is fittED With a
32amp
fUsE or BrEaKEr