4. OPERATING INSTRUCTIONS
Input Power . . . . . . . . . . . . . . .18V.DC. - 18W
Speed Range . . . . . . . . . . . . . .0 - 20 000 rpm
Speed Settings . . . . . . . . . . . . . . . . . .Variable
Collet Capacities . . . . . . . . . . . .1.2/1.8/2.4mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . .230g
Transformer Input . . . . . . . . . . .230V.AC 50Hz
Transformer Output . . . . . . . . . .18V.DC 1amp
2. TECHNICAL SPECIFICATION
E5885/50 - 1081 - (1) - 200400
4.1.
Connection
4.1.1. Ensure that On/Off switch (see fig.2) is in the Off position (OFF revealed on switch plate).
4.1.2. Insert plug on end of tool cable into socket in base of transformer (see fig.3).
4.1.3. Plug transformer lead into mains socket.
p
p
WARNING! Use only the transformer supplied. DO NOT connect the tool to any other type of power supply.
4.2.
Fitting accessories
4.2.1. Ensure tool is switched off and transformer is unplugged from the mains power supply.
4.2.2. Press the spindle lock button, see fig.4, and slowly turn the collet nut until the spindle lock engages.
4.2.3. Retain pressure on the spindle lock button and turn the collet nut anticlockwise to open the collet.
Note: Never press the spindle
lock button when the tool is running.
4.2.4. The required accessory may now be fitted into the collet. Fully insert accessory shaft to reduce risk of bending in use. Tightened
collet nut firmly. Finally release the spindle lock button.
4.2.5. To change collets, proceed as 4.2.1. to 4.2.3. but continue to unscrew collet nut until it can be removed from the spindle. Change
collets and replace collet nut. See fig.4.
4.2.6. Select the speed required on variable speed control. Small accessories require high speed and large accessories low speed. If in
doubt, start on a low setting and gradually increase until the best performance is obtained.
4.2.7. Check that On/Off switch is Off and then connect to mains supply. Turn On/Off switch to On.
DO NOT switch on with tool bit
touching workpiece. Always allow bit to reach full speed before applying to workpiece.
Note: If overloaded, the transformer will automatically cut-out. When overload is removed the transformer will reset.
fig. 2
fig. 4
3.1.
Check contents against the following list.
If any items are missing or damaged contact
your supplier immediately.
Tool
Transformer
Screwdriver
Spanner
Accessories - see fig.1
1) Cutting Disc x 10
2) Polishing Wheel x 6
3) Circular Saw x 5
4) Wheel Brush - Steel x 1, Brass x 1
5) Collet x 3 - Ø1.2, 1.8, 2.4mm
6) Grinding Bit - Cone
7) Grinding Bit - Small Cylinder
11) Tool Holder x 2 15) Ball Burr - Ø1.4mm
8) Grinding Bit - Large Cylinder
12) Sanding Band Holder x 2
16) Ball Burr - Ø2.3mm
9) Grinding Bit - Inverted Cone
13) Diamond Grinding Bit - Ø1.8mm
17) Burr - Inverted
Cone
10) Grinding Bit - Ball
14) Diamond Grinding Bit - Ø2.3mm
18) Twist Drill x 6 - Ø0.8, 1.0, 1.2, 1.4, 1.6, 1.8mm
3. CONTENTS
7
DO NOT
operate the tool if any parts are missing or damaged as this may cause failure and/or personal injury.
7
DO NOT
operate the tool when you are tired, under the influence of alcohol, drugs or intoxicating medication.
3
When not in use switch tool off, unplug transformer from the power supply, store both in the case and put in a dry, childproof area.
fig. 3
fig. 1
