fig.1
3. SPECIFICATION
4. OPERATION
Model No:
. . . . . . . . . . . . . . . . . . . . . . . . . . .
CP36S.V2
Battery: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6V
No Load Speed: . . . . . . . . . . . . . . . . . . . . . . . 0-200rpm
Maximum Torque: . . . . . . . . . . . . . . . . . . . . . . . . 3.5Nm
Charging Time: . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5hr
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.37m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5m/s²
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55dB(A)
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66dB(A)
fig.2
IMPORTANT WARRANTY INFORMATION:
The battery fitted to this cordless tool is considered to be a consumable item and its ability to accept charge will reduce over time. Our
warranty will cover genuine battery malfunction, but not fair wear and tear, for a period of 12 months.
3.1.
To charge the screwdriver, insert the charger jack into the charging socket on the screwdriver (fig.1) and plug the charger into a mains socket.
3.2.
The red indicator light (fig.2) will illuminate to indicate the battery is being charged. When charging is complete, unplug the charger from
the mains and the screwdriver. To check the level of charge, press the charge display button. When the green button is lit, the battery is fully
charged.
3.3.
Place a bit into the bit holder of the screwdriver. Select the required direction by using the reverse switch (which will lock the screwdriver in its
central position) and squeeze the trigger to start the screwdriver. The LED spotlight will light with initial pressure on the trigger.
3.4.
The LED worklight in the handle can be switched on or off by pressing the lens
3.5.
To check the condition of the battery, press and hold down the charge display button next to the charge indicator lights(fig.2). If all LEDs
illuminate, there is sufficient charge, if just the yellow and red LEDs illuminate, the screwdriver will soon need charging, if just the red LED
illuminates, the screwdriver needs to be charged immediately.
3.6.
To change the position of the handle, press the handle lock and turn the handle around 180° until it clicks into position (fig.2)
3.7.
To select torque or drill setting, twist the torque selector around
to the required setting - from 1 (the lowest) to 6 (the highest) for
torque setting or to the drill symbol for drilling.
3.8.
When finished working, remove the bit from the bit holder, pulling back the quick release bit holder if needed. Clean the screwdriver
and replace all parts in the storage case. Store the case in a safe, dry, child proof location.
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Battery Removal
To remove battery for disposal, unfasten the six screws in the grip then remove by cutting the connecting wires.
Dispose of the battery in accordance with local authority regulations.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential
purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s
registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Contents:
Screwdriver Bits: Slotted - 3, 4, 5, 6, 7mm, Phillips - #0, #1, #2, #3. Pozi:- #0, #1, #2, #3, TRX Star - T10, T15, T20, T25, T27, T30, T40,
T45, Hex - 2, 2.5, 3, 3.5, 4, 5, 6mm. 55mm Screwdriver Bits: Slotted - 4, 6mm. Phillips - #0, #2.Socket Adaptor. Sockets - 6, 7, 8, 9, 10, 11,
12, 13mm.
Magnetic Bit Holder.
Drill Bits - 1.5, 3mm.
CP36S.V2 Issue No:1 - 21/07/15
Original Language Version
© Jack Sealey Limited
