3.2.5.
To select 'hammer action' if required for drilling, turn the selector (fig.3.C) counter-clockwise aligning the hammer symbol with the
torque setting arrow on the main body. Turn the selector clockwise to return to the normal drill setting.
3.2.6.
There are 2 speeds controlled by the speed selector on top of the drill:
1 - slower speed - 0-350rpm
2 - higher speed - 0-900rpm
Select the appropriate speed as required.
3.2.7. Drilling.
Insert a pilot drill bit (a smaller sized drill than the required finished hole size) into the chuck and lock in position. Check to confirm the
rotational direction is correct (
DO NOT attempt to change direction whilst the drill is running).
After drilling the inital pilot hole, insert the final sized drill bit and drill out the hole to the appropriate size.
If the drill becomes stuck, release the trigger and place the drill in reverse and try running the drill slowly whilst moving the drill out of
the hole. If this does not work, gently work the drill bit free. If the chuck stops turning, check the torque setting.
3.2.8.
To check the condition of the battery, press and hold the battery indicator button next to the battery level indicator at the rear of the
drill.
3.2.9. When finished working, remove the bit from the chuck, clean drill and bit, and store in the case.
fig.3
Environmental protection.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging
should be sorted, taken to a recycle centre and disposed of in a manner which is
compatible with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way.
Battery Removal
Remove the battery pack - see section 3.1.1. Dispose of spent battery pack correctly.
onlY dispose of or recycle according to local authority regulations.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey ltd are required to inform potential purchasers
of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered
compliance scheme. Jack Sealey ltd’s Batteries Producer Registration number (BPRn) is BPRn00705
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMpORTANT:
no liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole Uk Distributor, Sealey Group,
Kempson Way, Suffolk Business
Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Original Language Version
Original Language Version
CP1801V.V3 Issue:1 - 08/03/10
CP1801V.V3 Issue: 3 - 12/01/12
fig.2
Risk of Hand Arm vibration Injury
Cordless Hammer Drill model no. CP1801V.V3 when operated in accordance with these instructions and tested in accordance with BS En
28662-1:1993, ISo 8662-1:1988 and BS En ISo 8662-6:1995, ISo 8662-6:1994 results in the following vibration emission declared in
accordance with BS En 12096:1996.
Measured vibration emission value:
0.46m/s²
Uncertainty:
0.18m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
This is a ‘
NO LOAD’
vibration figure.
A competent person should carry out a risk assessment following HSE guidelines.
Measurement results can be highly variable, depending on many factors, including the operator's technique, the condition of the work
equipment, the material being processed and the measurement method.
Recommended Measures to reduce risk of hand-arm vibration syndrome:
We recommend appropriate safety equipment is utilised and regular breaks for the operator are employed to reduce any residual risk of
fatigue or repetitive strain injury.
