1.3.
BATTERY SAFETY PRECAUTIONS
WARNING!
Battery contains Lithium-ion which is dangerous. Handle with care to avoid damage, fire, corrosion or personal injury.
9
Charge battery prior to its first use. The battery will have been shipped in a low charge state. To reduce the risk of burns or fire:
8
DO NOT
Attempt to open, disassemble, modify or service the battery pack.
8
DO NOT
Crush, puncture, short external contacts or dispose of in fire or water.
8
DO NOT
Expose to temperatures above 40°C (104°F).
9
Replace only with the battery pack designated for this product.
9
Use only the supplied charging base provided to charge the battery.
8
DO NOT
attempt recharging the battery by means of an engine generator or a DC power source.
WARNING!
Dispose of spent batteries correctly as they contain Lithium-ion.
DANGER
!
DO NOT
attempt to disassemble the
battery. For safety and environmental reasons
DO NOT
discard in domestic waste or by burning.
ONLY
discard or recycle
according to local authority regulations.
WARNING!
DO NOT
allow a leaking battery to contact your person.
1.4.
GENERAL SAFETY
9
Maintain the tool and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
9
Ensure the tool is switched off before installing the battery pack.
9
Keep the tool and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the tool; e.g. ceilings, floors and enclosures may contain electrical items or water piping.
9
Ensure battery pack is correctly inserted into the handle and latched in place before attempting to switch on tool.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Keep direction switch in the locked position until the tool is required for use.
9
Keep children and unauthorised persons away from the working area.
8
DO NOT
use the tool where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT
allow children to operate the tool.
8
DO NOT
operate the tool
if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT
hold unsecured work piece in your hand.
8
DO NOT
leave the tool operating unattended.
8
DO NOT
carry the tool with your finger on the power switch. Keep chuck direction switch in the locked position.
8
DO NOT
use the tool for a task it is not designed to perform.
8
DO NOT
operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
get the tool or battery charger wet or use in damp or wet locations.
2. INTRODUCTION
Compact, lightweight cordless impact drill. Comfortable housing with soft grip to reduce vibration. With variable speed and locking functions that
give more control during application. Integrated LED battery level indicator and LED work light. Supplied with 1 hour mains charger and 1 x 2Ah
rechargeable Lithium-ion battery.
3. SPECIFICATION
Model no ..............................................................CP108VDD
B
attery ............................... 10.8V 2Ah Lithium-ion (Included)
Chuck size ................................................................ Ø10mm
Consumable parts .............................
CP108VBP 2Ah battery
Impact frequency ...................................
0-6000/0-19500bpm
Max. torque ...................................................................28Nm
N
oise power/pressure
....................................
82.1/71.1dB(A)
No-load speed .............................................
0-400/0-1300rpm
Replacement parts .....................CP108VMC - mains charger
V
ibration/uncertainty
............................
1.987m/s², K=1.5m/s²
4. BATTERY CHARGING
4.1.
Fully charge the battery before first use.
WARNING!
Only recharge batteries with the charger supplied.
4.2.
Remove battery by squeezing buttons in on each side.
Insert into battery charger.
4.3.
Connect charger to mains supply and red LED will light to signal charging. Once charging is complete LED turns green.
4.4.
Remove from mains supply, remove battery and insert into tool until a click is heard.
4.5.
BATTERY CHARGE STATUS TEST
4.5.1.
Press trigger, all LEDs lit: battery charged, one LED lit: battery needs charging.
4.6.
In order to maintain battery efficiency:
DO NOT
fully discharge. After every use fully charge the battery, charge every 4 months even if tool is not used.
If a decrease of performance of the tool is noticed, charge the battery.
5. OPERATION
5.1.
Ensure the direction selector is in the mid (lock) position.
Original Language Version
© Jack Sealey Limited
C
P108VDD Issue:1 22/02/21
