background image

INSTRUCTIONS FOR

VEHICLE STORAGE SHELTER (2.7 X 5.5 X 2MTRS)

MODEL NO: 

CCS01

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAFETY

   NOTE: 

This is a temporary structure and is not recommended as a permanent structure.

 

9

   Choose your shelter’s location carefully. Check for overhead utility lines, branches, etc. 

DO NOT

 install near roofs or other structures that

   may shed snow, ice or excessive run-off onto your shelter. Keep away from electrical wires!

 

9

   Have an overview of all parts before attempting installation. Make sure all components are available.

 

8

   DO NOT

 use this product in environments for which it is not intended (i.e. extreme cold, high winds, extreme heat, heavy rainfall, etc).

 

9

   Always wear safety glasses when assembling this product. Wear gloves when working with tubing to prevent cuts or abrasions.

 

‰

  WARNING!

 Anchors must be used with alI shelters. Covers should 

NOT

 be installed untiI it has been properly anchored to the ground.

     NOTE:

 Proper anchoring and keeping cover tight and free of snow and debris, is the responsibility of the consumer. Damages caused  

    

by improper anchoring are not covered under warranty.

 

‰

  WARNING!

 

Keep all flame and heat sources away from the shelter fabric. The fabric will burn if left in continuous contact with a flame  

 source.

 

8

   DO  NOT

 use open flames or cooking or heating devices inside or in close proximity to the product, including all types of stoves, gas  

  heaters, gas lanterns, citronella torches, mosquito coils, etc.

 

‰

  WARNING!

 In order to reduce risk of burning and avoid damage, 

DO NOT:

 

 

  - cook, smoke, refuel or use any open flame devices in or around the shelter.

 

 

  - store flammable liquids (gasoline, kerosene, propane, etc.) in the shelter.

 

 

  - operate gas powered equipment in or around the shelter.

 

‰

  

WARNING!

 Keep open flames a safe distance away from the shelter.

 

8

   DO  NOT

 use hard-edged tools or instruments, such as rakes or shovels, to remove snow. These can cause punctures to the cover.

 

   NEVER

 start the engine of any vehicle or machine inside a closed shelter. Ensure that there is adequate ventilation for starting    

  engines and for any work with paints, cleaners, etc.

 

8

   DO  NOT

 use bleach, alkaline or harsh detergents for cleaning. Doing so will damage the polycarbonate material. Soap and warm  

  water are recommended.

 

9

   This temporary shelter is intended to offer protection from damages caused by the sun, light rain, light snow, tree sap, bird and animal  

 excrements. 

DO NOT 

use it to shield goods from high winds, heavy snow or ice storms. Only use it for its intended purpose.

2. 

INTRODUCTION

 

Made from durable anti-scratch material to protect vehicle’s paintwork. Rigid tubular frame with hinged opening for easy access.  

 

 

Hook and loop vents allow increased ventilation while still keeping vehicle protected from elements. Includes anchor points for fixing   

 

shelter to driveway/ground (fixings not included). Padlock hasp and additional ground anchor point for increased security when canopy is  

 

closed.   

3. 

SPECIFICATION

Model No: ...................................................................CCS01 

Dimensions (W x D x H) ..............................2.7 x 5.5 x 2 mtrs

4.  ASSEMBLY

4.1.    

ASSEMBLY PREPARATION

4.1.1.   

Place all parts from the packaging box in a cleared area and arrange them on the ground in front of you.

4.1.2.   

Remove all packaging materials and place them back in the box. 

DO NOT 

dispose of the packaging materials until assembly is 

 complete.

4.1.3.   

Check for completeness of components and transport damages.

 

 

‰

   WARNING! DO NOT

 place the product under trees from which hard fruit such as apples, walnuts or heavy pine cones, etc., may fall.

4.1.4.   

Keep children away during assembly. This product contains small parts which can be swallowed by children.

 

8

   DO NOT

 attempt to assemble the product if any parts are missing.

4.1.5.   

At least 2 people are needed to complete the assembly as some of the steps require awkward lifting and fitting.

 

‰

  WARNING! DO NOT

 leave the shelter unattended during assembly. Otherwise, personal injury or damage to the shelter may occur.

CCS01   Issue 1  13/04/18

Original Language Version

© Jack Sealey Limited

Refer to 

instruction

manual

Wear protective 

gloves

Wear eye

protection

Summary of Contents for CCS01

Page 1: ...te gas powered equipment in or around the shelter WARNING Keep open flames a safe distance away from the shelter 8 8 DO NOT use hard edged tools or instruments such as rakes or shovels to remove snow These can cause punctures to the cover NEVER start the engine of any vehicle or machine inside a closed shelter Ensure that there is adequate ventilation for starting engines and for any work with pai...

Page 2: ...e very similar to items D except they are slightly longer Take care to select the correct items C at this stage 4 2 2 Securely assemble centre spar using items M M6 x 60 bolt arrangement fig 3 Item I X4 Item J X1 Item K X1 Item L X1 Item M M6 x 60 X2 Item N M6 x 40 X24 A A C A B N fig 2 fig 1 E F B C B C fig 3 M CCS01 Issue 1 13 04 18 Original Language Version Jack Sealey Limited Item A X2 Item B ...

Page 3: ...ng the ground fixing tab item J fig 6 Draw the cover over the remaining spars and fix in place using the hook and loop tabs built into it 4 2 5 The shelter is provided with four anchor point plates ground fixings not supplied These are fitted to the main frame bases items A as shown in fig 7 and fig 8 Do not assemble ends at this stage D H fig 4 fig 5 Hook and loop tabs fig 6 A I Ground fixings NO...

Page 4: ...e environment When the product becomes completely unserviceable and requires disposal drain any fluids if applicable into approved containers and dispose of the product and fluids according to local regulations Note It is our policy to continually improve products and as such we reserve the right to alter data specifications and component parts without prior notice Important No Liability is accept...

Reviews: