background image

 compact auto smart charger 
(12a, 12/24V)

model no: 

autocharge1200hF

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions, 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  saFetY

1.1.          eLectrIcaL saFetY.

 

‰

  

WarNINg!

 It is the user’s responsibility to check the following:

 

Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and    

 

all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical  

 products. 

 

If the charger is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable  

 

 

Appliance Test) tested.

 

electrical safety information, it is important that the following information is read and understood.

 

9

   ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. 

 

9

   Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.

 

9

  

Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - see  

  fuse rating in these instructions.

 

8

   Do  Not

 pull or carry the appliance by the power cable.

 

8

  

Do Not

 pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.

 

8

   Do  Not

 use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or 

 

replaced immediately by a qualified electrician

.

 

This product is fitted with a BS1363/A 13 Amp 3 pin plug. 

 

9

      If the cable or plug is damaged during use, switch the electricity supply off and remove from use. 

 

9

   Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.

 

Class II products are wired with live (brown) and neutral (blue) only and are marked with

 

 the Class II symbol;

 

A) Connect the BROWN live wire to the live terminal ‘L’.

 

B) Connect the BLUE neutral wire to the neutral terminal ‘N’.

 

C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected. 

 

9

   ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight. 

 

8

   Do  Not 

connect either wire to the earth terminal. 

 

Sealey recommend that repairs are carried out by a qualified electrician. 

1.2.    

BatterY charger saFetY.

 

   DaNger! Be aWare, LeaD-acID BatterIes geNerate eXpLosIVe gases DurINg NormaL BatterY operatIoN.   

  For thIs reasoN, It VerY ImportaNt to reaD aND FoLLoW these INstructIoNs careFuLLY, each tIme You use  

  the chargINg eQuIpmeNt. 

 

9

  

Follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you intend to  

  use in the vicinity of the battery. Remember to review warning marks on all products and on engines.

 

‰

  

WarNINg!

 modern vehicles contain extensive electronic systems.

 

You are required to check with the vehicle Manufacturer, for any specific instructions regarding the use of this type of equipment on    

 

each vehicle.

 No liability will be accepted for damage / injury, where this product is not used in accordance with all instructions.

1.3.    

persoNaL precautIoNs.

 

9

 

ensure there is another person within hearing range of your voice and close enough to come to your aid, should a problem arise when  

  working near a lead-acid battery.

 

9

  

Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery.

 

9

   Have fresh water and soap nearby in case battery acid contacts skin, clothing or eyes.

 

9

   Wash immediately with soap and water if battery acid contacts skin or clothing. If acid enters eye, flush eye immediately with cool,    

  clean running water for at least 15 minutes and seek immediate medical attention.

Recommended fuse rating

5 amp

A

UTOCHARGE1200HF     Issue 1 22/08/18

Original Language Version

© Jack Sealey limited

      Refer to

   instructions

      electrical

        shock

       hazard

 

Wear eye

protection

 

Wear protective

gloves

 Warning

corrosive 

substance

 

Warning:

risk of explosion

 Keep away 

from sources of 

ignition

 

Use in well 

ventilated areas

 Keep in dry area 

protect from rain

Summary of Contents for Autocharge1200HF






Reviews: