manualshive.com logo in svg

SealerSales W Series, Manual

Share
Download
SealerSales W Series Manual Download Page 10

7. When sealer is not in use, turn off the power switch

Please note: Sealing bars will be extremely hot. Do not touch the

sealing bars as this could cause severe burns.

Tips for Successful Sealing

1. If the seal is broken or dam

2. If the seal is not fully welded, i

3. If the sealing material sticks to the

4. Always keep the sealer clean. Remove any residue found on the

used.

5.

Be sure to turn off the power or unplug the unit before replacing any parts.

9

When sealer is not in use, turn off the power switch.

Please note: Sealing bars will be extremely hot. Do not touch the

sealing bars as this could cause severe burns.

Tips for Successful Sealing

If the seal is broken or damaged, decrease the sealing time / temperature.

lded, increase the sealing time / temperature.

If the sealing material sticks to the sealing bars, decrease the sealing time / temperature.

Always keep the sealer clean. Remove any residue found on the sealing bars. Silicone spray may be

off the power or unplug the unit before replacing any parts.

sealing bars, decrease the sealing time / temperature.

sealing bars. Silicone spray may be

off the power or unplug the unit before replacing any parts.

Summary of Contents for W Series

















Reviews:

No comments

Brands by name

Popular brands

Load more brands