manualshive.com logo in svg

Seagull Models P47 SNAFU, Instruction Manual

Share
Download
Seagull Models P47 SNAFU Instruction Manual Download Page 2

P47 SNAFU

Instruction Manual.

2

 

Thank you for choosing the 

P47 SNAFU

 ARTF by 

SEAGULL MODELS COMPANY LTD

,. 

The 

P47 SNAFU

 was designed with the intermediate/advanced sport flyer in mind. It is a semi 

scale airplane which is easy to fly and quick to assemble. The airframe is onventionally built using 

balsa, plywood to make it stronger than the average ARTF, yet the design allows the aeroplane 

to be kept light. You will find that most of the work has been done for you already. The motor 

mount has been fitted and the hinges are pre-installed. Flying the 

P47 SNAFU

 is simply a joy.

This instruction manual is designed to help you build a great flying earoplane. Please read 

this manual throughly before starting assembly of your 

P47 SNAFU

. User the parts listing 

below to indentify all parts.

 

Please be awere that this aeroplane is not a toy and if assembley or used incorrectly it is 

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU 

ASSUME ALL RISK & REPONSIBILITY.

If you are inexperianced with basic R/C flight we strongly recommend you contact your R/C 

supplier and join your local R/C model Flying Club. R/C Model Flying Clubs offer a variety 

of training procedures designed to help the new pilot on his way to successful R/C flight. 

They will also be able to advise on any insurance and safety regulations that may apply.

INTRODUCTION.

WARNING.

KIT CONTENTS

3

1

5

2

3

2

4

6

7

8

Summary of Contents for P47 SNAFU







































Reviews:

No comments

Brands by name

Popular brands

Load more brands