manualshive.com logo in svg

Seagate ST32122A - Medalist 2.1 GB Hard Drive, Installation Manual

Share
Download
Seagate ST32122A - Medalist 2.1 GB Hard Drive Installation Manual Download Page 35

Medalist 4342, 3232 and 2122, Rev. C

31

Seagate Technology support services

Online services

Internet
Visit Seagate on the Internet at http://www.seagate.com for infor-
mation about Seagate products. You can also send e-mail with
your disc or tape questions to:
Presales: 

[email protected] 

or

[email protected]

Technical support:

[email protected] 

or

[email protected]

SeaBOARD

®

SeaBOARD is a computer bulletin board system that contains
information about Seagate disc and tape drive products and is
available 24 hours daily. Set your communications software to
eight data bits, no parity and one stop bit (8-N-1).

Presales support

Presales support
Our Presales support staff can help you determine which
Seagate products are best suited for your specific application or
computer system.

Seagate Express
You can purchase select tape products and tape accessories
through Seagate Express 24 hours daily by calling 1-800-531-
0968 or by faxing your order to: 1-972-481-4812.

Summary of Contents for ST32122A - Medalist 2.1 GB Hard Drive

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands