background image

Seagate SkyHawk AI Serial ATA Product Manual, Rev. C

  8

  

2.3

Recording and interface technology  

2.4

Start/stop times 

Power-on to ready time is based on typical operating conditions, default full current spin-up profile, and clean shutdown prior to 
measurement. To ensure a clean shutdown a Flush Cache, Standby, or Standby Immediate command must be completed before 
removal of interface power.

An unexpected power loss event, spin up at cold or hot temperature extremes may cause the drive to exceed the typical and max 
time to ready by 5 to 20 seconds. Extended time to ready is dependent on cache state and environmental conditions prior to the 
unexpected power loss and during the subsequent power on.

2.5

Power specifications

The drive receives DC power (+5V or +12V) through a native SATA power connector. See 

Figure 3 on page 17

.

2.5.1

Power consumption

Power requirements for the drives are listed in 

Table 2

. Typical power measurements are based on an average of drives tested, under 

nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature.

Interface

Serial ATA (SATA)

Recording method

Perpendicular

Recording density, KBPI (Kb/in max)

2499

Track density, KTPI (ktracks/in, 0 Skew)

487

Areal density (Gb/in

2

, @ 0 skew mid-disk)

1215

Spindle speed (RPM) (± 0.2%)

7200

Internal data transfer rate (Mb/s max)

2169

Sustained data transfer rate (MiB/s max)

234 (245 MB/s max)

I/O data-transfer rate (MB/s max)

600 (Ultra DMA mode 5)

Power-on to Ready (sec) (typ/max)

23/30

Standby to Ready (sec) (typ/max)

23/30

Ready to spindle stop (sec) (max)

20

Table 2

DC Power Requirements (5-disk models)

Power Dissipation

Avg (25°C) (Watts)

Avg 5V typical (Amps)

Avg 12V typical (Amps)

Spinup (max)

2.0A

Idle

1

1.

During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational 
levels.

*           Based on IDEMA 3 Stream workload

7.76

0.325

0.512

Operating

*

10.09

0.542

0.6144

Standby

0.96

0.185

0.003

Sleep

0.96

0.185

0.003

Summary of Contents for SKYHAWK SURVEILLANCE AI 5 E Series





























Reviews: