background image

Seagate BarraCuda Pro Serial ATA Product Manual, Rev. A

www.seagate.com

Drive specifications

*See 

Section 1.2.10, "Reliability"

 for rated MTBF device operating condition requirements.

Temperature gradient (°C per hour max)

20°C (operating)

 

30°C (nonoperating)

Relative humidity

*

5% to 95% (operating)

 

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

Altitude, operating

–304.8 m to 3,048 m

 

(–1000 ft to 10,000+ ft)

Altitude, nonoperating (below mean sea level, max) –304.8 m to 12,192 m

 

(–1000 ft to 40,000+ ft)

Operational Shock (max at 2 ms - typical)

Read 70 Gs / Write 40 Gs

Non-Operational Shock (max at 2 ms - typical)

250 Gs

Vibration, operating

5–22 Hz:       0.25 Gs, Limited displacement

 

22–350 Hz:    0.50 Gs

 

350–500 Hz:  0.25 Gs

Operation Rotational vibration

20–1500Hz: 12.5 rads/s²

Vibration, nonoperating

2–500 Hz:    2.27 Grms ref

Drive acoustics, sound power (bels)

     Idle

1.8  (typical)

 

2.0     (max)

 

During periods of drive idle, some offline activity may occur according to the 

 

SMART specification, which may increase acoustic and power to operational levels

.

     Performance seek

2.6  (typical)

 

2.8     (max)

Nonrecoverable read errors

1 sector per 10

15 

bits read

Annualized Failure Rate (AFR)

*

1% based on 8760 POH

Maximum Rated Workload

*

Maximum rate of <300TB/year

Workloads exceeding the annualized rate may degrade the drive MTBF and impact prod-
uct reliability. The Annualized Workload Rate is in units of TB per year, or TB per 8760 
power on hours. Workload Rate = TB transferred * (8760 / recorded power on hours).

Warranty

To determine the warranty for a specific drive, use a web browser to access the following 
web page: 

http://www.seagate.com/support/warranty-and-replacements/

.

From this page, click on the “Is my Drive under Warranty” link. The following are required 
to be provided: the drive serial number, model number (or part number) and country of 
purchase.The system will display the warranty information for the drive.

Load-unload cycles 

300,000

Supports Hotplug operation per

 

Serial ATA Revision 3.3 specification

Yes

Drive specification

ST14000DM001

ST12000DM001

ST10000DM001

Summary of Contents for Barracuda Pro ST10000DM001






















































Reviews: