background image

Seagate SkyHawk Product Manual, Rev. E

  29

 Serial ATA (SATA) Interface 

4.3.1

Identify Device command

The Identify Device command (command code EC

H

) transfers information about the drive to the host following power up. The data is organized as 

a single 512-byte block of data, whose contents are shown in 

Table 14

. All reserved bits or words should be set to zero. Parameters listed with an “x” 

are drive-specific or vary with the state of the drive. Refer to 

Drive Specifications

 on page 7 for default parameter settings.

The following commands contain drive-specific features that may not be included in the Serial ATA specification.

Table 14 Identify Device command

Word

Description

Value

 

 

0

Configuration information:

 

• Bit 15: 0 = ATA; 1 = ATAPI

 

• Bit 7: removable media

 

• Bit 6: removable controller

 

• Bit 0: reserved

0C5A

H

1

Number of logical cylinders

16,383

2

Specific configuration

C837H

3

Number of logical heads

16

4

Retired

0000

H

5

Retired

0000

H

6

Number of logical sectors per logical track: 63

003F

H

7–9

Retired

0000

H

10–19

Serial number: (20 ASCII characters, 0000

H

 = none)

ASCII

20

Retired

0000

H

21

Retired

8000

H

22

Obsolete

0004

H

23–26

Firmware revision: (8 ASCII character string, padded with blanks to end of string)

x.xx

27–46

Drive model number:

 

(40 ASCII characters, padded with blanks to end of string)

ST1000LV000

 

ST2000LV000

47

(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write multiple (16)

8010

H

48

Trusted Computing Feature set options

4001

H

49

Standard Standby timer, IORDY supported and may be disabled

2F00

H

50

Capabilities

4000

H

51

PIO data-transfer cycle timing mode

0200

H

52

Retired

0200

H

53

Words 54–58, 64–70 and 88 are valid

0007

H

54

Number of current logical cylinders 

xxxx

H

55

Number of current logical heads 

xxxx

H

56

Number of current logical sectors per logical track

xxxx

H

57–58

Current capacity in sectors

xxxx

H

59

Number of sectors transferred during a Read Multiple or Write Multiple command

xxxx

H

60–61

Total number of user-addressable sectors
This field contains a value that is one greater than the total number of

 

user-addressable sectors. The maximum value that shall be placed in this field is 
0FFFFFFFh. The 0FFFFFFFh value applies to all capacities over 137GB 

 

(see 

Section 2.1, Formatted Capacity

 for related information).

ST1000LV000 = 0FFFFFFFh

 

ST2000LV000 = 0FFFFFFFh

62

Retired

0000

H

63

Multiword DMA active and modes supported (see note following this table)

xx

07

H

Summary of Contents for SkyHawk ST1000LV000





































Reviews: