background image

Seagate SkyHawk Product Manual, Rev. E

  9

 Drive Specifications 

2.2

Physical organization  

2.3

Recording and Interface Technology

2.4

Physical Characteristics

2.5

Seek time

Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications 
in the table below are defined as follows:
• Track-to-track seek time is an average of all possible single-track seeks in both directions.
• Average seek time is a true statistical random average of at least 5000 measurements of seeks between random tracks, less overhead.

Drive model

Read/write heads

Number of discs

ST2000LV000

4

2

ST1000LV000

2

1

Interface

SATA 6Gb/s

Recording method

Perpendicular

Recording density 

2276 Kb/in

Track density 

580 ktracks/in avg

Areal density 

1320 Gb/in

avg

Spindle speed 

5400 RPM

Data transfer rate (up to)

140 MB/s

 Height (mm/in)

7.0 (± 0.2) / 0.276 (± 008)

 Width (mm/in)

69.85 (± 0.25) / 2.750 (± 0.010)

 Length (mm/in)

100.35 (+0.20/-0.25) / 3.951 (+0.008/-0.010)

Typical weight (g/lb)

90 / 0.198

Cache buffer

128MB

Table 2

Typical seek times

Typical seek times (ms)

Read 

Track-to-track

1.5

Average

13.0

Average latency

5.6

Note

These drives are designed to consistently meet the seek times represented in this manual. Physical seeks, 
regardless of mode (such as track-to-track and average), are expected to meet the noted values. However, due

 

to the manner in which these drives are formatted, benchmark tests that include command overhead or 
measure logical seeks may produce results that vary from these specifications.

Summary of Contents for SkyHawk ST1000LV000





































Reviews: