SeaDoo Rotax 1503 4-Tec 2005 Page 55 Engine Shop Manual Download

Page: 55 / 124

Section 01 ENGINES (1503 4-TEC)

Subsection 04 (LUBRICATION SYSTEM)

R1503motr118A

1. Oil inlet to the oil pump

Installation

For installation, reverse the removal procedure.

Refill engine at the proper level with the recom-
mended oil. Refer to LUBRICATION SYSTEM in
the appropriate

VEHICLE SHOP MANUAL

for the

procedure.

SUCTION PUMP OIL STRAINER

NOTE:

The oil strainer does not need to be

cleaned at every oil change. Clean it during other
inspections, especially when the engine is disas-
sembled.

Removal

– Remove ventilation hose

no. 7

R1503motr133A

TYPICAL — NATURALLY ASPIRATED AND
SUPERCHARGED ENGINES

1. Ventilation hose

R1503motr374A

TYPICAL — SUPERCHARGED INTERCOOLED ENGINE

1. Ventilation hose

– Disconnect wiring harness from TOPS valve

no. 8

and oil separator pressure switch (OSPS)

no. 9

– Detach intake hose from throttle body (naturally

aspirated engine only).

– Remove other required parts from vehicle to

access the oil suction pump cover.

– Remove retaining screws

no. 10

and

no. 11

– Place rags under cover to prevent spillage. If

spillage occurs, clean with the pulley flange
cleaner (P/N 413 711 809) .

SMR2005-035

www.SeaDooManuals.net

Summary of Contents for Rotax 1503 4-Tec 2005





























































































































Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands

SeaDoo Rotax 1503 4-Tec 2005, Engine Shop Manual

Search results

Summary of Contents for Rotax 1503 4-Tec 2005

Reviews:

Related manuals for Rotax 1503 4-Tec 2005

Brands by name

Popular brands