background image

MAINTENANCE OF YOUR UNIT

Beginning of Season

PRIOR TO OPERATION
• Carefully inspect both indoor and outdoor unit for blockages of
  the inlet and outlet exhaust vents.
• Inspect ground connection. Ensure that ground wire is properly
  connected.
• Inspect Air Filters and clean if necessary.
• Install new batteries in the remote control unit ( 2 ea “AAA”).

During the Season

CLEANING THE AIR FILTERS
• Filters should be cleaned every 2 weeks or more often if the unit
  is used continuously or the unit is operated in a high dust area.

TO REMOVE THE AIR FILTERS:
• To open the indoor unit, pressing on the outside edges of the
  lower corners of the cover and pull outwards. The front cover 
  will swing upwards. DO NOT OPEN FRONT COVER FURTHER
  THAN STOPS. DO NOT FORCE THE FRONT COVER OPEN.

• To remove the filters, push the filter upwards from the bottom to
  release.

• Clean the filters by washing in lukewarm water (about 86°F).
  Allow the filters to dry before re-installing. DO NOT USE HOT
  WATER. DO NOT USE HARSH CHEMICALS.

• Re-install clean filters by sliding the filter in at the top then
  locking behind tabs on the bottom.

• DO NOT OPERATE THE UNIT WITHOUT THE FILTERS IN
  PLACE. DAMAGE TO THE UNIT COULD OCCUR.

NOTICE: Performance of this unit is greatly reduced when operated
with dirty, damaged, or clogged filters.

AFTER THE OPERATING SEASON
• Set the temperature to 86°F and operate the unit in the FAN
  MODE for about  4 - 6 hours to thoroughly remove any moisture
  from the interior of the unit.

• Turn the unit off. In the OFF mode, the unit still comsumes
  about 5 watts of power. If you wish to completely turn the unit
  off, turn off the breaker to the unit.
• Clean and re-install the air filters.
• Clean both the indoor and outdoor units.
• Remove the batteries from the remote control and store the
  remote control in a safe place.

If you have a problem with your unit, please check the following
items BEFORE calling for service:

TROUBLESHOOTING

If the unit will
not operate

Is there power at the   Is the remote control   Is the timer on
unit                                operating

Check for tripped        Point remote at unit     Check the TIMER
breaker or blown         and press the power    status. If the TIMER is
fuse                               button. You should      on, press
                                      hear a “BEEP” if the    “AUTOSTART” button
Turn breaker off for     unit is receiving a         to cancel timer
30 seconds then turn  signal from the              operation.
                                      remote.

                                      Replace batteries in
                                      remote. 

If the unit will

operate but not

cool

 Is there remote set      Is there air flow?          Is unit sized properly?
 properly                               

 Set temperature           Check for clogged      Check with
 lower than current       filter.                             Installation contractor
 room temperature.       Check for blocked
 Verify that unit is in     intake or outlets.
 “COOL” mode.             Check fan mode
 Unit takes 3 minutes
 to restart after
 shutdown. 

-9-

Summary of Contents for 12H43YCX













Reviews: