Sea Tel 5009-17, Installation Manual

Page: 58 / 145

5009-17 Installation Manual Setup – Searching
10-4
10.2.1.
Sets offset of AGC tracking threshold above the average noise floor. Units are in A/D counts, approximately
20 counts/dB. A setting of 0 disables auto threshold, therefore, the operator would have to manually enter a
threshold value.
AUTO THRES
When AUTO THRESHOLD is enabled (any value between 1-255), the ACU automatically re-sets the AGC
tracking threshold whenever the antenna Targets (AZ, EL or SAT) or Searches. The new AGC threshold is set
to the average signal level input (approximate background noise level) plus the AUTO THRES offset value.
EXAMPLE: If the Noise Floor off satellite is 1000 counts of AGC and Auto Threshold is set to 100, Threshold
will be set to approximately 1100 after the antenna has finished targeting or Searching.
To change the Automatic Threshold value OR manually set threshold; Note the Peak “on satellite” AGC value,
move EL and note the “off satellite” (Noise Floor) AGC value. Calculate the Difference between Peak AGC and
Noise Floor AGC. AUTO THRES should be set to 1/3 (to ½) of the Difference. This will usually be around 100
counts (3 dB) for a typical antenna configuration. Changes to this parameter may be required based on
carrier tracking frequency, possible adjacent satellite, or ambient interference with desired satellite.
To manually update, press the LEFT arrow key to bring the cursor up under the least significant character.
Continue to move the cursor until the desired character to be edited is underscored (selected). Use the UP or
DOWN arrow keys to increment or decrement the selected character.
Use the LEFT or RIGHT arrow key to move the cursor left or right to select other characters to modify. When
you are finished modifying press ENTER to execute the new value OR press NEXT to abort and exit setup
mode.
10.2.2.
For proper DishScan operation this parameter must be set to factory default value of 0000.
EL STEP SIZE
To manually update, press the LEFT arrow key to bring the cursor up under the least significant character.
Continue to move the cursor until the desired character to be edited is underscored (selected). Use the UP or
DOWN arrow keys to increment or decrement the selected character.
Use the LEFT or RIGHT arrow key to move the cursor left or right to select other characters to modify. When
you are finished modifying press ENTER to execute the new value OR press NEXT to abort and exit setup
mode.
10.2.3.
For proper DishScan operation this parameter
must
be set to factory default value of 0000.
AZ STEP SIZE
To manually update, press the LEFT arrow key to bring the cursor up under the least significant character.
Continue to move the cursor until the desired character to be edited is underscored (selected). Use the UP or
DOWN arrow keys to increment or decrement the selected character.
Use the LEFT or RIGHT arrow key to move the cursor left or right to select other characters to modify. When
you are finished modifying press ENTER to execute the new value OR press NEXT to abort and exit setup
mode.
10.2.4.
For proper DishScan operation this parameter
must
be set to factory default value of 0000.
STEP INTEGRAL
To manually update, press the LEFT arrow key to bring the cursor under the least significant character.
Continue to move the cursor until the desired character to be edited is underscored (selected). Use the UP or
DOWN arrow keys to increment or decrement the selected character.
Use the LEFT or RIGHT arrow key to move the cursor left or right to select other characters to modify. When
you are finished modifying press ENTER to execute the new value OR press NEXT to abort and exit setup
mode.
10.2.5.
Sets size of search pattern increment. Units are in pedestal step resolution (12 steps per degree). The
suggested setting is equal to the full 3dB beamwidth of your antenna. Default value is 15 these systems.
SEARCH INC
To manually update, press the LEFT arrow key to bring the cursor under the least significant character.
Continue to move the cursor until the desired character to be edited is underscored (selected). Use the UP or
DOWN arrow keys to increment or decrement the selected character.
Use the LEFT or RIGHT arrow key to move the cursor left or right to select other characters to modify. When