background image

SU11 LongBoard

If you ordered the portable bat-

tery, connect the battery to the 

quick connector onto the pump 

.

To charge the portable battery, 

plug it into the charger and then 

plug the charger into a house-

hold electrical outlet. The light 

on the battery charger will blink 

red until fully charged. When it 

is fully charged the light will be 

a solid green.

Keep the pump in its carry bag 

to make transportation easier 

and to protect the pump from 

sand which could jam it. The 

carry bag has compartments for 

the pump, battery hose.

Press the ON button to begin in-

flation. The pump operates in two 

stages which can be identified by 

the noise of the turbine at the 

start, followed by the piston. 

The pump automatically 

stops once the pressure is 

reached. 

Air compressors that are de-

signed for other uses like tire 

inflation (usually around 50 PSI) 

can easily harm your Sea Eagle 

SUP which works at a much 

lower pressure of 12-15 PSI. For 

this reason we recommend only 

using Sea Eagle pumps.

Locate you orange repair kit. In-

side it you will find the gray re-

cessed valve adapter.

Take the  recessed valve adapter 

and firmly push it into the grey 

tube in the end of the hose. To 

ensure that the adapter is fully 

seated on the tube, push it until 

the end of the tube pushes past 

the raised ring in the adapter.

Connect the other end of the 

hose to the red inflation port at 

the top of the pump, located 

near the ON and OFF buttons.

Adjust the pressure dial to read 

12-15 PSI which is the operating 

pressure of your Sea Eagle. PSI 

is marked in red on the dial. 

Never turn the dial when the 

device is under pressure as this 

will immediately cause the in-

strument to break.

Do not exceed 15 PSI

Connect the quick connector at 

the end of the power cord into 

the quick connector attached to 

the pump.

To connect the pump to a 12V 

battery, use the cord with alliga-

tor clips at the end of the exten-

sion cord. Connect the red clip 

to the positive pole and the 

black clip to the negative pole. 
CAUTION: Cross connecting 

wires could damage the pump 

and boat.

Summary of Contents for LongBoard SUP LB11












Reviews: