Sea-doo GTI 5865 Shop Manual Download

Page: 40 / 316

03-00-2

Section 03

TROUBLESHOOTING

ENGINE MISFIRES, RUNS IRREGULARLY

ENGINE OVERHEATS

ENGINE CONTINUALLY BACKFIRES

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Weak spark

• Fouled, defective, worn spark plugs

• Faulty rev limiter or ignition

• Sheared flywheel key

• Check / verify heat range / gap / replace

• Check, refer to section 08-02

• Check timing mark, refer to section 08-02

Lean fuel mixture
Dry spark plug (except when
water fouled)

• Low fuel level

• Stale or water fouled fuel

• Fuel filter dirty or restricted

• Carburetion dirty or out of adjustment

• Leaking crankshaft seal(s), intake or rotary

valve cover

• Restricted fuel valve

• Loose carburetor

• Check / refill

• Check / siphon and refill

• Check / clean / replace

• Check / clean / adjust, refer to section

06-03

• Check / test / replace, refer to engine sec-

tion 04-03 and 04-04

•

Check / replace

• Tighten carburetor(s)

Rich fuel mixture
Fouled spark plug

• Partially closed choke

• Flame arrester dirty or restricted

• Carburetor adjustment or setting

• Loose main jet

• Rotary valve shaft seal leaking

• Oil pump adjustment

• Worn needle(s) and seal(s)

• Excessive rotary valve clearance

• Check / adjust choke cable

• Check / clean / replace

• Check / clean / adjust, refer to section 06-03

• Check, refer to section 06-03

• Check / replace, refer to section 04-04

• Check / adjust, refer to section 07-02

• Check, refer to section 06-03

• Check, refer to section 04-04

Difficult to start

• Incorrect rotary valve timing

• Excessive rotary valve clearance

• Check / adjust, refer to section 04-04

• Check, refer to section 04-04

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Monitoring beeper sounds
continuously

• Restricted jet pump water intake

• Cooling system restriction

• Grounded temperature sensor or sensor

wire

• Check / clean

• Check / flush, refer to section 02-02

• Check / repair / replace

OTHER OBSERVATION

POSSIBLE CAUSE

REMEDY

Weak spark

• Fouled, defective spark plugs

• Malfunction of rev limiter

• Clean / replace

• Clean / replace, refer to section 08-02

Ignition timing

• Incorrect setting

• Sheared flywheel key

• Check / reset, refer to section 08-02

• Check / replace, refer to section 08-02

Rotary valve

• Incorrect timing

• Check / reset, refer to section 04-04

Carburetor

• Carburetion to lean

• Check / adjust, refer to section 06-03

Engine

• Intake leak / crankshaft seal failure

• Pressure check engine to 48 kPa (7 PSI)

www.SeaDooManuals.net

Summary of Contents for GTI 5865





























































































































































































































































































































Search results

Summary of Contents for GTI 5865

Reviews:

Related manuals for GTI 5865

Brands by name

Popular brands

Sea-doo GTI 5865, Shop Manual

Search results

Summary of Contents for GTI 5865

Reviews:

Related manuals for GTI 5865

Brands by name

Popular brands