Sea-doo 1997 GS Operator'S Manual Download Page 2

Page: 2 / 105

◆

SAFETY WARNING

Disregarding any of the safety precautions and instructions contained in
this

Operator’s Guide, the Safety Handbook and on Warnings Labels

could cause injury, including the possibility of death.

This

Operator’s Guide, the Safety Handbook and videocassette should

remain with the watercraft at the time of resale.

AFTER-SALES
SERVICE
BOMBARDIER INC.
VALCOURT (QUÉBEC)
CANADA J0E 2L0

The following trademarks are property of
Bombardier Inc.:

SEA-DOO

Bombardier Lube

Sea-Doo Jet Pump Synthetic Oil
Sea-Doo Synthetic Grease

Gelcote

is a trademark of Gelcote International

Litho’d in Canada (SMO-9701 PRM)

*Trademarks of Bombardier Inc.

Bombardier Inc. 1996

smo9701a.bk : smo9701a.toc Page 0 Monday, November 3, 1997 9:54 AM

www.SeaDooManuals.net

Summary of Contents for 1997 GS









































































































Search results

Summary of Contents for 1997 GS

Reviews:

Related manuals for 1997 GS

Brands by name

Popular brands

Sea-doo 1997 GS, Operator'S Manual

Search results

Summary of Contents for 1997 GS

Reviews:

Related manuals for 1997 GS

Brands by name

Popular brands