950-0206revE
- 9 -
February 12, 2015
-5 ºF to +75 ºF in the heating mode. Indoor fan will turn off in heating mode when temperature
set point has been satisfied.
DRY mode – Set point temperature can be set from 61°F to 86°F. Unit cools at 90% capacity
while the FAN runs in LOW speed only (FAN speed cannot be changed).
FAN mode – Selects fan only operation. Set point temperature can be set from 61 °F to 86 °F.
Fan speed can be set to AUTO, HIGH, MEDIUM or LOW.
SLEEP
– In the COOL mode adjust the set-point temperature to a comfortable setting, and then
press the SLEEP button. After 1 hour, the set-point will increase by 1.8 ºF (1 ºC). After 2 hours have
passed temperature is increased by 3.6 ºF (2 ºC). Temperature will never increase more than 3.6 ºF (2
ºC) from set-point or beyond 86 ºF (30 ºC). The temperature will stay at this setting until the unit is
turned off or the SLEEP function is disabled.
In the HEAT mode adjust the set-point temperature to a comfortable setting, and then press the SLEEP
button. After 1 hour the set-point will decrease by 1.8 ºF (1 ºC). After 2 hours have passed temperature
is decreased by 3.6 ºF (2 ºC). Temperature will never decrease more than 3.6 ºF (2 ºC) from set point or
below 61 ºF (16 ºC). The temperature will stay at this setting until the unit is turned off or the SLEEP
function is disabled.
The SLEEP mode does not work in the FAN or AUTO modes and is deactivated when the unit is turned
off or power is lost. On power up, the SLEEP mode must be turned on again if needed. Press the
SLEEP mode button to toggle SLEEP mode off and return to normal operation.
FAN
– Press this button to change fan speeds, AUTO, HIGH, MEDIUM or LOW, while in the HEAT,
COOL, FAN modes. When in the AUTO setting, the fan will run faster the further away from the set
point it gets. On the other hand the closer it gets to the set point the slower it will run.
CLOCK
– Press the CLOCK button, the clock ICON will start to blink. It will only blink for 5
seconds. While blinking press and hold down the + or - keys to adjust the 24H time of day clock to the
correct time. You must immediately press the CLOCK button to set the time. If the CLOCK button is not
pressed within 5 seconds, the clock time will revert back to the original setting and clock will have to be
set again.
PURGE
/
BLOW
– When in the COOL or DRY mode and the PURGE function is enabled, the fan
will continue to operate for 10 minutes after the unit is turned off. This function dries the evaporation coil
to prevent mold and mildew. The PURGE function will remain enabled in DRY and COOL unless power
is interrupted or is disabled by the button. PURGE will not work in AUTO, FAN or HEAT modes.
TURBO
– The TURBO function will only run while in the HEAT or COOL mode. TURBO increases
indoor fan speed (more than high fan speed). This function is not activated for Cassette unit.
+
/
-
Raises or Lowers the set point temperature
. Holding the button down for more than 2 seconds
will cause the set point to auto increment or decrement. This does not function in the AUTO mode since
the temperature set point cannot be changed.
DISPLAY
– Turns the display on or off on the indoor unit. None of the lights will be illuminated
when off is selected.
SWING
– Pressing the louver positioning button slowly, (more than 2 seconds) will start and stop
the louver swing. If the button is pressed to turn on swing and then
pressed again to turn it off, the louvers will remain in that fixed position
until it is turned on again.
Pressing the button quickly, (less than 2 seconds) will step through 5
different stationary positions and then on to 3 different swing positions, similar to the ICONS.
LOCK KEYPAD -
Pressing the + and - buttons simultaneously will lock or unlock the keypad. If the
remote control is locked, the LOCK icon will be displayed. If a button is pressed while the keypad is
locked, the LOCK icon will blink three times, nothing will happen. If the keypad is unlocked, the LOCK
icon will not be displayed.
