manualshive.com logo in svg

SDL Atlas Vortex M6, Instruction Manual

Share
Download
SDL Atlas Vortex M6 Instruction Manual Download Page 39

                                                    __________________                                      Vortex M6  

 

32

Reinstallation of Shipping Materials 

 
You must install the shipping brace and shipping plug any time the Vortex M6 is moved. 
 

Shipping Brace 

 
The shipping brace in the lid opening should be saved and reinstalled whenever the Vortex 
M6 is moved. To reinstall the brace, open the lid and place the brace over the instrument 
agitator, placing the back of the brace into the lid opening first. 
 

Shipping Plug 
 

The  plastic  shipping  plug  should  be 
saved  and  reinstalled  any  time  the 
Vortex M6 is moved. The plug fits into 
two  openings:  The  base  opening  and 
the  shipping  plug  opening  on  the 
bottom  of  the  movable  pivot  dome. 
The  plug  MUST  be  inserted  into  both 
openings  to  prevent  damage  to  the 
instrument. In order to accomplish this, 
the  shipping  plug  opening  must  be 
directly lined up with the base opening. 
 
 
After  the  shipping  brace  has  been 
installed  in  the  lid  opening,  tilt  the 
Vortex M6 back enough to access base 
opening.  Insert shipping plug into base 
opening  and,  using  the  palm  of  your 
hand,  push  shipping  plug  into  the 
instrument  until  it  snaps  into  shipping 
plug opening. 

Summary of Contents for Vortex M6











































Reviews:

No comments

Brands by name

Popular brands

Load more brands