SDL Atlas Vortex M6 Instruction Manual Download Page 20 | Manualshive

Page: 20 / 42

background image

__________________ Vortex M6

13

Earth/Ground Instructions

This  instrument  must  be  properly  connected  to  protective  earth/ground.  In  the  event  of
malfunction  or  breakdown,  the  earth/ground  will  reduce  the  risk  of  electric  shock  by
providing a path of least resistance for electric current.

The Vortex M6 must be plugged into an appropriate outlet that is properly installed
and  connected  to  a  protective  earth/ground  in  accordance  with  all  local  codes  and
ordinances.

• DO NOT modify the plug provided with the instrument – if it will not fit the outlet, have a
proper outlet installed by a qualified electrician.

«
...
18
19
20
21
22
...
»

Summary of Contents for Vortex M6











































Reviews:

No comments

Related manuals for Vortex M6

Brand: DBX Bushido Pages: 12

Brand: Halyard Pages: 88

Brand: HALDER Pages: 2

Brand: IBEX Pages: 4

Brand: EuroLite Pages: 28

Lab companion SI-300

Brand: Jeio tech Pages: 69

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 4

Brand: Jct Pages: 16

Brand: Haas Pages: 12

Brand: SaMASZ Pages: 25

Brand: Lafayette Pages: 10

Brand: WARPP Pages: 28

Brand: Safco Pages: 2

Brand: Salter Pages: 18

Brand: Salter Pages: 42

Brand: Salter Pages: 47

Brand: Salter Pages: 35

Brand: Salter Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands