Scytek electronic A10 SERIES Product Manual Download Page 10

Optional Coded Emergency Override 

As an extra measure of security, the system is equipped with an optional Coded Emergency Override

feature. Once an Emergency Override Code is chosen and programmed during installation, the system can

no longer be disarmed using the standard override procedure. 
To Emergency Override the system using the Code:

1. Follow steps 1-3 above. 
2. Press the override switch a number of times equal to the Disarm code, and continue holding for

10 seconds on the last press.

· The system will disarm.  If the code is entered incorrectly, turn off the ignition and begin again.

To set the Emergency Override Code:

1. Turn on ignition.
2. Within 5 seconds, press the valet switch 5 times.

· The siren will provide one long chirp, indicating that you have entered Programming.

3. Press the valet switch 3 times.

· The siren will chirp each time the valet switch is pressed.

4. Within 5 seconds, press Button 3 on the transmitter.

· The siren will chirp 3 times.

5. Press the valet switch the number of times equal to the desired code (from 1-15).
6. Turn off the ignition then arm the system.
7. Disarm the system using the new Override Code to permanently store the new code.

Note: If the code set procedure is not properly performed, turn off the ignition and begin again.  The override code will not

be permanently stored until the code is used to disarm the system.

Valet Mode

The Valet Mode temporarily disables the security system so the vehicle may be operated by a mechanic or

parking attendant.
To activate or deactivate the Valet Mode:

1.  Turn on the ignition.
2.  Press and hold the override switch for 5 seconds.

· The siren will chirp once and the LED light will stay ON to confirm the Valet Mode is on.
· The siren will chirp twice and the LED light will turn OFF to confirm the Valet Mode is off.

3.  Turn off the ignition.

While in Valet Mode the remote transmitters will continue to lock and unlock the doors, and operate the

optional auxiliary functions. 

Page 6 -  Astra A10

Summary of Contents for A10 SERIES





















Reviews: