manualshive.com logo in svg

Screen Innovations Zen Box, Owner'S Manual, Page: 13 / 15

Share
Download
Screen Innovations Zen Box Owner'S Manual Download Page 13

POWER (MOTORIZED ONLY)

Power connection exits out of the back of the box on the side specified when ordered. Use 
appropriate building codes and run and connect the power cable to an appropriate outlet. Note, you 
can run the power cord through the track assembly if needed.

Hot Black

Neutral White

Ground Green

To be installed and/or used in accordance with the appropriate electrical codes and 
regulations by a licensed electrical professional. Do not connect power with the circuit 
breaker on.

Before connecting power to multiple units be aware that the limits must be set with power 
connected to only one unit at a time. Plan accordingly.

Step 1. Connect Power

With the motor installed in shade, connect power to the motor 120V

Step 3. Check Directions

Press      or      . While pressing      product should go down or out. To change direction press 
and hold      (Stop) until shade jogs. A jog is a brief up and down motion.

Step 2. Initiate Programming 

Press both      and      at the same time until the shade jogs. A jog is a brief up and down 
motion. In Programming Mode, the shade will move only when the       or      is held.

Step 4. Set the Limits

Bring the shade to desired upper limit stop point. Press both       (Stop) and       until the 
motor moves, then release. (If the shade stops when the buttons are released take it back to 
the upper limit and repeat). Stop the motor when reaching the desired lower limit. You can 
adjust by pressing       or     .

Step 7. Set user mode

Press and hold the programming button on the back of the transmitter until the shade jogs. 
The shade is now in User Mode.  In User Mode, the shade will operate with a brief press on           
      or     . Double check limit settings as a precaution.

Step 5. Set the Limits

Press both       (Stop) and      at the same time until the shade moves, then release. The 
shade  will stop at the original upper limit.

Step 6. Confirm limit settings

Press and hold       (stop) unitl the shade jogs to confirm the limit settings. A jog is a brief up 
and down motion.

SET LIMITS (MOTORIZED ONLY)

my

my

my

my

my

my

my

my

my

Programming mode

Before you begin

Motors are shipped without limit settings and transmitter ID’s.  Steps 1 to 7 must be completed to ensure 
proper shade programming and functionality. Power should ONLY be connected to current shade being 
programmed.  All other shades should be disconnected from their respective power while programming 

Zen Box - Power (Motorized only)

Zen Box - Set limits (Motorized only)

Pg 21

Pg 22

Summary of Contents for Zen Box
















Reviews:

No comments