Scraper Systems FleetPlow 110S Base-Mount Owner'S Manual Download Page 2

 

 

 

Table of Contents 

 

 

Manufacturer’s Warranty, 

page 2 

Operating Information and Requirements,

 pages 2-3 

Conversion for Rolling (Portable Models Only),

 page 4 

Operating Procedure for OneTAP™ Full Automation,

 page 4 

Operating Procedure for Standard Automation with AutoUP™,

 page 4 

Operating Procedure for Manual Operation (using pendant control), 

pages 5-6

 

Multi-Trailer Operation, 

page 6

 

Maintenance,

 pages 7-8 

Troubleshooting,

 pages 8-11 

OneTAP Load Spring Piston Proximity Sensor Installation,

 page 11 

Drawings,

 pages 12-16 

Parts Lists,

 pages 17-19 

 

 

North American Warranty 
 

Scraper Systems FleetPlows™ are warranted, from the date of shipment, to be free from defects in material and workmanship for a 

period of two (2) years on all mechanical and electrical parts and one (1) year for labor, based on approved travel and labor repair times. 
The FleetPlow must be used in accordance with manufacturer’s recommendations and must not have been subject to abuse, lack of 

maintenance, misuse, negligence, or unauthorized repairs or alterations. The FleetPlow must have been installed by certified dealer 
installers or by factory installers, with training on the safe and proper operation provided by same.  

 

 
 

 
 

NOTICE:  FleetPlows are designed for safe and effective snow clearing in controlled commercial applications.  Like with all large machines, 

care must be taken by all personnel in the vicinity to uphold common sense safety practices and operate the machine only as it is 

intended.  Failure to do so may result in damage to this or other equipment and/or personal injury or death. 

 

 
 

Key Tips for Optimal FleetPlow™ Performance 

 

1.

 

LEVEL TRAILER. 

Minimize any slope, front to back or back to front. 

 
2.

 

CENTER THE TRAILER

 by aligning vehicle with the V-point of the plow. 

 
3.

 

MINIMIZE CHAIN SLACK

 to 2 links or less when plow is resting on roof. (OneTAP automation is pre-programmed.) 

 
4.

 

REMOVE GROUND SNOW

 as necessary. Avoid snow build-up beneath the FleetPlow. 

 

5.

 

ACCELERATE TO 8-10 MPH

 while passing under the plow, clearing the snow off the vehicle roof.

 

 

Summary of Contents for FleetPlow 110S Base-Mount






















Reviews: