manualshive.com logo in svg

Scotsman Prodigy Elite MC0322, Service Manual

Share
Download
Scotsman Prodigy Elite MC0322 Service Manual Download Page 59

MC0322 through MC2148

Air, Water, and Remote Cooled Service Manual

January 2022 

Page 59

Repair Section

Inlet Water Solenoid Valve
1 Disconnect electrical power

2 Shut off the water supply.

3 Remove front and left side panels.
4 Unplug wire from coil.
5 Disconnect water supply tube from the
inlet of the valve.
6 Disconnect the water outlet tube.
7 Remove the two mounting screws holding the valve to the back panel.
8 Pull the valve forward and out of the machine.
Fan Blade or Motor

1 Push and release the Off button

2 Disconnect electrical power.
3 Remove front panel and left side panel.
4 Unplug fan motor wire leads.
5 Remove fan motor mounting brackets from shroud. Note: Fastener size is 3/8” hex
6 Carefully remove fan motor and blade assembly from machine cabinet.
7 Loosen set screw, pull fan blade from motor shaft.
8 If the blade is the only part being changed, reverse to reassemble. Note: blade mounts
purge to end of motor shaft.
9 If the motor will be changed, remove mounting brackets from fan motor. Note: Fastener
size is ¼” hex.
10 Reverse to reassemble.

Electrical Shock Hazard
Disconnect electrical 

power before beginning

Summary of Contents for Prodigy Elite MC0322















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands