background image

What to do before calling for service

Normal Operation

Ice

The machine will make either flaked or nugget ice,
depending upon the model. The ice will be
produced continuously until the bin is full.

Heat

Most heat is exhausted at the remote condensing
unit or at the rack; the ice machine should not
generate significant heat.

Noise

The ice machine will make noise when it is in ice
making mode. The gear reducer will produce
sound. Some ice making noise could also occur.
These noises are all normal for this machine.

Reasons the machine might shut itself off:

Lack of water.

Does not make ice

Auger motor overloaded

Controller self test failure.

Check the following:

1. Has the water supply to the ice machine or
building been shut off? If yes, the ice machine will

automatically restart within minutes after water
begins to flow to it.

2. Has power been shut off to the ice machine? If
yes, the ice machine will automatically restart when
power is restored.

3. Has someone shut the power off to the remote
condensing unit while the ice machine still had
power? If yes, the ice machine may need to be
manually reset.

To Manually Reset the machine.

• Push and release the Off button.

• Push and release the On button.

To Shut the Machine Off:

1. Push and hold the Off button for 3 seconds or
until the machine stops.

July 2009

Page 16

N0622L, F0822L, N0922L, F1222L, N1322L, F1522L
Remote Low Side User's Manual

Indicator Lights & Their Meanings

Light Actions

Power

Status

Water

De-Scale &
Sanitize

Steady Green

Normal

Normal

-

-

Blinking Green

Self Test Failure

Switching on or off.
When Smart-Board
used, machine attention
recommended.

-

-

Blinking Red

-

Diagnostic shut down

Lack of water

-

Yellow

-

-

-

Time to descale
and sanitize

Blinking Yellow

-

-

-

In Cleaning Mode

Light Off

No power

Switched to Off

Normal

Normal

All Blinking

Unit is remotely locked out - check with leasing company

Summary of Contents for F0822



















Reviews: