background image

C0322 through C1030

Air and Water Cooled User Manual

November 2012

Page 9

Panel Removal

1.  Locate and loosen the two screws at the front 

edge of the top panel.

2.  Pull the front panel out at the top until it clears the 

top panel.

3.  Lift the front panel up and off the machine.

4.  Remove two screws at the front of the top panel. 

Lift up the front of the top panel, push the top 

panel back an inch, then lift to remove.

5.  Locate and loosen the screw holding each side 

panel to the base. Left side panel also has a 

screw holding it to the control box.

6.  Pull the side panel forward to release it from the 

back panel.

This manual covers several models. The model 

number on the product is located in two places, on the 

back dataplate and on the model and serial number 

tag, located behind the front panel. See the illustration 

for the dataplate and serial tag locations.

Write the model and serial number of this product 

here:

________________________________________

Write the day, month and year of initial start up here:

________________________________________

Switch Bezel

All models ship with the On and Off switches front 

accessible. If desired, the On and Off switches can be 

covered up to prevent unauthorized use by changing 

the bezel in the front panel’s trim strip. A cover up 

bezel is available from the local Scotsman distributor.

Push snaps of standard bezel in and pull the bezel 

out of the front panel trim strip.

Locate other bezel. Push into the trim strip from the 

front until it snaps into place. Return the front panel to 

its original position and secure it to the cabinet.

Uncrate and Set Up

Begin with unpacking the ice storage bin. Remove the 

carton, and using part of the carton as a cushion, tip 

the bin on its back to remove the skid and attach the 

legs or casters.

Return the bin to an upright position. Check the bin 

top gasket for gaps and tears, fill any in with food 

grade sealant prior to placing the ice machine on the 

bin.

Install the bin top adapter or ice dispenser adapter, if 

one is required for the application.

If the ice machine has not been unpacked, do so now. 

Remove the carton from the skid. Lift the ice machine 

off the skid directly onto the bin.

Note: The machine is heavy! Use a mechanical hoist 

if necessary.

Secure the ice machine to the bin with the hardware 

provided (two metal straps and 4 bolts).

Place the bin and ice machine in the selected location 

and level it by adjusting the bin leg levelers.

Datatplate Location and Panel Removal

Dataplate 

Location

1. Remove 

Screws

5. Remove 

Screws

2

6

4

6

3

Summary of Contents for C0830MA-32





































Reviews: