scope ConneXions II V7 MAC Installation & User Manual Download Page 11

Page: 11 / 13

ConneXions II V7 MAC Mains, Multi Port Version

CONV7MAC 05/98

Issue 1

System Specification

Mains Input:

230V 50Hz

Mains Power Consumption:

6W max

System Operating Voltage:

13.8V dc

System Power Consumption:

less than 50mA standby, 300mA (transmit)

Transmitter:

Power output:

500mW

Frequency Range:

450-470 MHz

Channel Spacing:

25 KHz or 12.5KHz

Adjacent Channel:

better than 200nW @ 4.5 KHz deviation

TX Baud Rate:

512 or 1200

Type Approval:

ETS 300 224, MPT1383 Cert. No. 13249

Type Approval No.

13249 CONX7AC

EMC Approval:

EC Type Approved to ETS 300 682 Approval No: 13331

General:

Ports:

RS232 serial on PL1, PL2 and PL3

Optional 10 way dry contact I/F on PL1

Comms Baud Rate:

PL1, PL2: 1200 Baud. PL3: 9600 Baud*

Footprint (mm):

328 (L) x 190 (W) x 75 (D) max

*dependent on system configuration

excluding aerial

Scope’s policy is one of continuous development and specifications are subject to change without notice

Summary of Contents for ConneXions II V7 MAC














Search results

Summary of Contents for ConneXions II V7 MAC

Reviews:

Related manuals for ConneXions II V7 MAC

Brands by name

Popular brands

scope ConneXions II V7 MAC, Installation & User Manual

Search results

Summary of Contents for ConneXions II V7 MAC

Reviews:

Related manuals for ConneXions II V7 MAC

Brands by name

Popular brands