scinco Mega-900 UV-Vis Instruction Manual Download

Page: 2 / 46

Mega-900

SCINCO

Introduction

Thanks for your purchase of the SCINCO CO., LTD. Mega-900 spectrophotometer.

UV-Visible Spectrophotometer is a well-accepted, documented technique with many

applications. The technique is extensively used for the analysis of agricultural

products and is widely used in public health, environmental protection, life sciences

industries and many other organic and biochemical applications.

For obtaining maximum performance and trouble-free operation, we give you the

following suggestions:

◆

Upon receiving your instrument, please check all the items listed in the

packing list are included and install the instrument according to the instruction

manual.

◆

The spectrophotometer is a precise electronic instrument. Please read the

instruction manual carefully before operation. If the equipment is used in a

manner not specified by the manufacturer, the protection provided by the

equipment may be impaired.

◆

Avoid collision and handle the instrument carefully during transportation.

◆

If the tested solution is harmful to humans, please wear gloves or use other

protection methods.

◆

Please keep the accessories in a safe place for the use in future maintenance.

For more information, please visit

www.scinco.com

Summary of Contents for Mega-900 UV-Vis















































Search results

Summary of Contents for Mega-900 UV-Vis

Reviews:

Related manuals for Mega-900 UV-Vis

Brands by name

Popular brands

scinco Mega-900 UV-Vis, Instruction Manual

Search results

Summary of Contents for Mega-900 UV-Vis

Reviews:

Related manuals for Mega-900 UV-Vis

Brands by name

Popular brands