background image

 

 

12

BlueSpin

 (Hotplate) Magnetic Stirrer

 

Changes or modifications not expressly approved by the 
party responsible for compliance could void the user's 
authority to operate the equipment.   
NOTE: This equipment has been tested and found to 
comply with the limits for a Class A digital device, 
pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful 
interference when the equipment is operated in a 
commercial environment. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed 
and used in accordance with the instruction manual, may 
cause harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to 
cause harmful interference in which case the user will be 
required to correct the interference at his own expense. 
 
 
 
 
 
 
 
 

11.

 

Specifications 

Items 

Specifications 

Digital model 

Classic 

model 

Voltage [VAC] 

*100~120/200~240 

100~240 

Frequency [Hz] 

50/60 

50/60 

Power [W] 

*515/15 

10 

Stirring point position 
quantity 

1 1 

Max. stirring quantity 
(H

2

O) [l] 

3 3 

Max. magnetic bar [

L×Ø

mm] 

50 50 

Motor type 

DC motor 

Max. power input of 
motor [W] 

5 5 

Max. power output of 
motor [W] 

3 3 

Speed range [rpm] 

100 – 1500, 

increment:10 

0 – 1500 

Rotary speed display 

LED 

Scale 

Summary of Contents for MS-H280


















Reviews: