SmartMeter
3/4
CONFIGURATION CYCLE
To enter the configuration cycle, press
BACK
and
SET
. The meter
displays
typ.1
,
the first parameter of the cycle. To access the
remaining parameters ofthis cycle, press
SET
.
Keys
and
make possible to change the parameters defined. To access the
measures screen, go to the end of this cycle or press keys
BACK
and
SET
again.
The parameters of the configuration cycle are:
typ.1
Selects the channel 1 sensor according to Table 1. Channel 1 sensor
is chosen regardless of the channel 2 sensor selection.
typ.2
Selects the channel 2 sensor according to Table 1. Channel 2 sensor
is chosen regardless of the channel 1 sensor selection. Channel 2
indication can be disabled.
Code
Input
oFF
Channel 2 - disabled
0-50
0-50 mV
Rtd
Pt100
Tc b
B thermocouple
Tc s
S thermocouple
Tc r
R thermocouple
Tc n
N thermocouple
Tc e
E thermocouple
Tc t
T thermocouple
tc h
K thermocouple
tc j
J thermocouple
Table 1
dP.P1
(Decimal Point Position)
Enables the display of decimal points for channel 1 measures.
Parameter not valid for thermocouples
R, S
and
B
. For the 0-50 mV
input, defines the decimal point position.
dP.P2
(Decimal Point Position)
Enables the display of decimal points for channel 2 measures.
Parameter not valid for thermocouples
R, S
and
B
. For the 0-50 mV
input, defines the decimal point position.
In.l1
(Lowest indication limit of channel 1 for 0-50 mV)
Determines the inferior limit of the user-created meter indication
range, when the 0-50 mV input signal is selected. Parameter not
displayed for the other input types.
In.k1
(Highest indication limit of channel 1 for 0-50 mV)
Determines the upper limit of the user-created meter indication range,
when the 0-50 mV input signal is selected. Parameter not displayed
for the other input types.
In.l2
(Lowest indication limit of channel 2 for 0-50 mV)
Determines the inferior limit of the user-created meter indication
range, when the 0-50 mV input signal is selected. Parameter not
displayed for the other input types.
In.k2
(Highest indication limit of channel 2 for 0-50 mV)
Determines the upper limit of the user-created meter indication range,
when the 0-50 mV input signal is selected. Parameter not displayed
for the other input types.
0fs.1
(Indication Offset, channel 1)
Allows for an offset in the temperature value displayed in channel 1.
The offset value is simply added to the value measured by the
sensor. The offset can be of 10 % of the selected sensor maximum
range, upwards or downwards.
0fs.2
(Indication Offset, channel 2)
Allows for an offset in the temperature value displayed in channel 2.
The offset value is simply added to the value measured by the
sensor. The offset can be of 10 % of the selected sensor maximum
range, upwards or downwards.
beep
(Beep – Sound alarm)
It enables or disables the sound alarm
Beep
=
no
: disabled
Beep
=
yes
: enabled
Note
: The
ALARM
message is displayed regardless of the sound
alarm status (on or off). To stop beeping while an alarm condition is
present, press any key.
Sh.0f
(
shut-off
– Auto power off)
It makes possible to define a time interval in which the meter powers
off automatically, provided no key is pressed within the interval.
Adjustable between 3 and 120 minutes.
vnit
(Unit – Temperature indication unit)
It defines the temperature unit of the meter.
ºC
for degrees Celsius and
ºF
Fahrenheit.
Filt
(Noise filter)
It adapts the meter frequency to the mains voltage in order to
optimize the internal noise filter. Such adaptation reduces possible
temperature oscillations, resulting from the mains frequency. Options
are:
50
- for 50 Hz mains.
60
- for 60 Hz mains.
Fvnc
(Special functions)
Defines whether special functions HOLD, AVG, MAX, MIN and
RELAT will be applied to channels 1 and 2 or only to channel 1.
Ch1
- special functions applied only to channel 1.
Ch1
- special functions applied to channels 1 and 2
4.4
CALIBRATION CYCLE
To enter the calibration cycle, press
BACK
and
SET
for 10 seconds. The
meter displays
soft
,
the first parameter of the cycle. To access the
remaining parameters of this cycle, press
SET
.
Keys
and
make possible to change the parameters defined. To access the
measures screen, go to the end of this cycle or press keys
BACK
and
SET
again. The parameters of the configuration cycle are:
Soft
(Software version)
About information. Informs the software review installed.
8888
(Serial Number)
About information. Informs the meter serial number. The four larger
numbers are the most significant and the smaller the less significant.
L(.(1
(
L
ow
C
alibration Channel 1)
INPUT OFFSET CALIBRATION
: Adjusts the lowest limit of the input
signal indication range (offset). In order to change the indicated
value, it may be required to press
or
several times.
k(.(1
(
High
C
alibration Channel 1)
INPUT SPAN CALIBRATION
: Adjusts the highest limit of the input
signal indication range (span). In order to change the indicated value,
it may be required to press
or
several times.
(j.Lo
Adjusts the room temperature where the meter is held. Important
information for calculations and meter internal compensation.
