8.19
Date Code 20120126
Instruction Manual
SEL-2032 Communications Processor
Serial Port Communications and Commands
Command Set
*>>
SER 2 BL <Enter>
<STX>
SER Data Points from attached device
Port ELEMENT FAST SER INDEX
2 52A 0
2 CLOSE 1
2 ALARM 2
2 IN101 3
<ETX>
*>>
Figure 8.28
SER Command With BL Option
SET
Use the
SET
command variations (Access Level 2) to configure the
SEL-2032. These
SET
command variations are listed in
with their
parameters, formats, and uses.
lists the editing keys used with all
SET
commands.
SET M
has some additional editing features, which are
described in
Math/Data Movement (SET M) Settings on page 7.31
.
The
SET
command always requires a class parameter (P, A, U, M, L, O, G, or
R). If the setting is port specific, the class is P, A, M, L, O, or U and you must
supply the port position (1
–
16 or F). Classes P, A, M, L, O, or U may also be
used with port numbers 17 and 18. You can give these parameters in any order,
for example,
SET 1 A
or
SET A 1
. The default
SET
command starts with the
first setting for the setting class. You may override the default and specify the
first setting displayed for editing by entering it as a
SET
parameter. For
example, type
SET 1 A ISSUE1
to jump directly to the ISSUE1 setting for
Port 1.
Basic, but intelligent, port configurations are established with
SET P
commands. You apply the advanced communication, control, and database
features of the SEL-2032 with the
SET A
,
SET U
,
SET M
,
SET L
,
SET O
,
SET R
, and
SET G
commands. On Ports 17 and 18 of the SEL-2032,
SET P
,
SET A
, and
SET U
are used to modify the settings of a plug-in card. The
settings that are presented in response to these commands are a function of the
installed card. See the plug-in card instruction manual to learn about its
settings.
to move
settings between ports.
for an explanation of all the settings, including
their applicability to various connected device types.
Table 8.4
Examples of Variations on the SET Command
(Sheet 1 of 2)
Command
Action
Format
Application
SET P
n
Enter Port ID.
Set all port configuration
and communication
parameters.
a,b
SET P
SET P 1
SET P 2 PARITY
Set current port
Set Port 1
Set Port 2 starting at
entry PARITY
SET A
n
Define automatic message
and trigger sequences.
b,c
Determine response
handling for messages.
Set data
parsing conditions.
SET A
SET A 4
SET A 3 ISSUE1A
Set current port
Set Port 4
Set Port 3 starting
with ISSUE1A
Summary of Contents for SEL-2032
