Schweitzer Engineering SEL-2032 Instruction Manual Download Page 227 | Manualshive

Page: 227 / 354

background image

8.11

Date Code 20120126

Instruction Manual

SEL-2032 Communications Processor

Serial Port Communications and Commands

Command Set

DEVCODE

Device Code

PARTNO

Part Number: Reserved for future use

CONFIG

Configuration: Reserved for future use

SPECIAL

Reserved for future use

An example command response is shown in

*

ID <Enter>

"FID



SEL-2032-R100-V0-Z000000-D20021222","08D6"

"BFID



SLBT-2030-R103-V0-Z000000-D20001226","095C"

"CID



507D","025D"

"DEVID



"COMMUNICATIONS PROCESSOR - S/N 97312004”,”0A70”

"DEVCODE



52","030E"

"PARTNO



","0281"

"CONFIG



000000","0383"

"SPECIAL



","02AE"

*

Figure 8.16

ID Command

The four digits at the end of each line are the 16-bit checksum in ASCII-
hexadecimal for the preceding string. This checksum is calculated by
summing the character codes starting with the first quotation mark and going
through the comma separating the string and checksum.

You can also use the

WHO

or

STATUS

command to determine

ID

information. The

ID

command provides consistency between the SEL-2032

and the new standard

ID

command format for SEL relays.

Add a port number to the

ID

command (

ID

p

, where

p

is any valid port

number 1–16) to obtain the FID, BFID, and DEVID of the device connected
to that port of the SEL-2032. Use a port number of 17 or 18 to determine the
FID and device name of an installed protocol card, as shown in

.

*

ID 17 <Enter>

"SEL-2701-R113-V0-Z000000-D20010102","07BA"
"BFID



SLBT-2701-R103-V0-Z000000-D20001228","0967"

"DEVID



Ethernet","0558""

*

Figure 8.17

ID Command for Installed Protocol Cards

IRIG

The

IRIG

command (Access Level 1), as shown in

, directs the

SEL-2032 to read the IRIG-B time-code input at the IRIG-B port on the back
panel.

If it reads the time code successfully, it updates the internal clock/calendar
time and date. The SEL-2032 then sends its ID, date, and time to the terminal.

*>

IRIG <Enter>

COMMUNICATIONS PROCESSOR - S/N 95012004 Date: 03/07/95 Time: 09:06:33

*>

Figure 8.18

IRIG Command

If the IRIG-B signal is not present or cannot be read, the SEL-2032 sends the
error message “IRIG-B DATA ERROR.” If the signal is present but the global
TIMESYNC setting is not set to IRIG, the SEL-2032 will display the error
message, “IRIG SIGNAL PRESENT BUT NOT PROCESSED DUE TO
TIMESYNC SETTING.”

Courtesy of NationalSwitchgear.com

«
...
225
226
227
228
229
...
»

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

AllShare Cast Dongle

Brand: Samsung Pages: 2

Brand: D-Link Pages: 14

Mini Field Agent

Brand: GE Pages: 87

Brand: IEI Technology Pages: 187

Brand: IEI Technology Pages: 71

Brand: Accuphase Pages: 2

Brand: ADTRAN Pages: 2

AMB-VDX3H1 Series

Brand: Acrosser Technology Pages: 4

Brand: Baldor Pages: 34

Brand: AOpen Pages: 18

Brand: Abit Pages: 22

Suzie-Q 541.35.520

Brand: Hafele Pages: 12

Brand: ekwb Pages: 11

Brand: Kontron Pages: 62

Data Capture Board CLC-CAPT-PCASM

Brand: National Semiconductor Pages: 15

RDGD3160I3PH5EVB

Brand: NXP Semiconductors Pages: 21

Brand: Xinje Pages: 76

Brand: Juniper Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands