manualshive.com logo in svg

Schweitzer Engineering SEL-2032, Instruction Manual

The Schweitzer Engineering SEL-2032 Instruction Manual is a comprehensive guide designed to assist users in operating this cutting-edge product efficiently. With step-by-step instructions and detailed explanations, this manual is available for free download on our website. Unlock the full potential of your SEL-2032 today at manualshive.com.

Share
Download
background image

7.30

SEL-2032

 

Communications Processor

Instruction Manual

Date Code 20120126

Settings

User-Defined (SET U) Commands

Table 7.7

User-Defined (SET U) Settings 

Setting

Comment

Description

CMD_EN

a

Enable SEL-2032 Commands (Y/N). 

You enter N (No) to disable the SEL-2032 command set.
This setting is only available for Master ports.

CMD_CH

a

Command termination character. 

You may define the command termination character with this 
entry. This setting is only available if CMD_EN is set to N (No); 
it is forced to <CR> otherwise. Changing this character from 
<CR> disables prompting on this port. Setting range is any single
character or control character.

CMD_CNT

a,

 

b, c

Number of general-purpose commands
(0–8). 

You enter a number (0–8) to enable command strings (CMD1–
CMD8). (0–4) on SEL IED and other IED ports.

CMD1–8

a

 or 

CMD1–4 

Command String 1-8 (Master ports)
or Command String 1–4 (SEL, Other ports). 

You enter the string that the SEL-2032 watches for to control the 
associated CMD bit. Each string is limited to 39 characters.

STR_EN

Enable use of special-purpose commands 
(Y/N). 

You set to Y (Yes) to enable use of the special-purpose
user-defined commands. For Master ports only.

TRANS

Initiate transparent mode sequence. 

You define a character sequence that the SEL-2032 watches for to 
initiate transparent communications. This setting is only available 
if STR_EN is set to Y (Yes). Must include \P.../ port number 
string. This string is limited to 39 characters.

TRANSACK

Transparent mode acknowledge. 

You define the response string the SEL-2032 uses if an entry into 
transparent mode is successful. This setting is only available if 
STR_EN is set to Y (Yes). This response string is limited to 1000 
characters.

TRANSNACK

Transparent mode denial. 

You define the response string the SEL-2032 uses if an entry into 
transparent mode is unsuccessful. This setting is only available if 
STR_EN is set to Y (Yes). This response string is limited to 1000 
characters.

READ

Read data. 

You define the character sequence the SEL-2032 watches for to 
perform a data read operation. You must include \P../ and \A../ 
strings. This setting is only available if STR_EN is set to Y (Yes). 
This string is limited to 39 characters.

READACK

Read data normal response. 

You define the response string the SEL-2032 uses if a read
operation is successful. Must include \D.../ string. This setting is 
only available if STR_EN is set to Y (Yes). This response string is 
limited to 1000 characters.

READNACK

Read data error response.

You define the response string the SEL-2032 uses if a read
operation is not successful. This setting is only available if 
STR_EN is set to Y (Yes). This response string is limited to 1000 
characters.

WRITE

Write data. 

You define the character sequence the SEL-2032 watches for to 
perform a data write operation. Must include \P.../, \A.../ and \D.../ 
strings. This setting is only available if STR_EN is set to Y (Yes). 
This string is limited to 39 characters.

WRITEACK

Write data success response. 

You define the response the SEL-2032 uses if a write
operation is successful. This setting is only available if STR_EN 
is set to Y (Yes). This response string is limited to 1000 charac-
ters.

WRITENACK

Write data error response. 

You define the response the SEL-2032 uses if a write
operation is unsuccessful. This setting is only available if 
STR_EN is set to Y (Yes). This response string is limited to 1000 
characters.

a

Valid for use with Ports 17 and 18, depending on installed card.

b

You may define up to eight command strings: CMD1

–

CMD8.

c

If CMD_CH is set to <CR>, the SEL-2032 will ignore nonprinting characters entered on the port. Therefore, you should not use nonprinting 
characters in user-defined commands unless you change the termination character.

Courtesy of NationalSwitchgear.com

Summary of Contents for SEL-2032



































































































































































































































































































































































Reviews:

No comments

Related manuals for SEL-2032

XDS 910 Reference Manual preview
910
Brand: XDS Pages: 99
TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Brand: TC Electronic Pages: 33
Yamaha mLAN Driver Manual Book preview
mLAN Driver
Brand: Yamaha Pages: 24
Yamaha DSP1D Supplementary Manual preview
DSP1D
Brand: Yamaha Pages: 5
Broadcom Brocade X6-8 Director Hardware Installation Manual preview
Brocade X6-8 Director
Brand: Broadcom Pages: 207
AYRSTONE AyrMesh IndoorAP Instructions preview
AyrMesh IndoorAP
Brand: AYRSTONE Pages: 2
Lanner NCA-1525 User Manual preview
NCA-1525
Brand: Lanner Pages: 78
Z3 Technology SBE264-10-RPS User Instructions preview
SBE264-10-RPS
Brand: Z3 Technology Pages: 87
Lutron Electronics Smart Bridge Quick Start Manual preview
Smart Bridge
Brand: Lutron Electronics Pages: 4
Omron JUSP-NS500 Datasheet preview
JUSP-NS500
Brand: Omron Pages: 6
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Brand: GarrettCom Pages: 10
Adaptec 2410SA - Serial ATA RAID Controller Hardware Installation Manual preview
2410SA - Serial ATA RAID Controller
Brand: Adaptec Pages: 14
CopperOptics 150-1342-01 Manual preview
150-1342-01
Brand: CopperOptics Pages: 12
Cypress Semiconductor CY7C1441AV33 Specification Sheet preview
CY7C1441AV33
Brand: Cypress Semiconductor Pages: 31
Cypress Semiconductor CY8CNP102B Specification Sheet preview
CY8CNP102B
Brand: Cypress Semiconductor Pages: 38
Cypress Semiconductor CY7C68023 Specification Sheet preview
CY7C68023
Brand: Cypress Semiconductor Pages: 9
Xilinx ML52 Series User Manual preview
ML52 Series
Brand: Xilinx Pages: 36

Brands by name

Popular brands

Load more brands