background image

 

       

4SN/L5,4BN/L6 Manual

                     IM080630

 

    RD: JUNE 2008  

RL: 1A 

BA 

 

8.  OPERATION AND LIGHTING INSTRUCTIONS:  

Page 10 

‘AAA’ Battery 

TO TURN ON: 

 

1.  From ‘OFF’ position, turn knob 90° counter-clockwise push and hold in. 

2.  Press the igniter until a flame is established. 

3.  Release the knob and check if the flame stays on. 

4.  If the flame goes out, repeat steps 1 & 2 above. 

5.  For maximum temperature, turn knob fully counter-clockwise. 

 

TO TURN OFF: 

 

1.  Turn the knob clockwise until it stops. 

2.  Depress knob and  turn fully clockwise to shut of the gas supply completely 

 

Warning: 

A 5 minute complete shut off period is required before the appliance is re-lighted. 
 

In very strong winds, turn off the heater, turn off the gas cylinder valve.  
Allow the heater to cool down before moving it to a sheltered location.

  

DO NOT

 move the heater while it is hot. 

Install ‘AAA” Battery into electronic igniter 
(as illustrated) by unscrewing cap 
counterclockwise, insert battery with 
positive terminal facing “in”. Replace cap. 

Summary of Contents for InfraSave 4BL6

















Reviews: