background image

Basic safety notes

04.00 | UFG 66 | Assembly and Operating Manual | en | 389470

13

2.14 Notes on particular risks

 DANGER

Risk of fatal injury from suspended loads!

Falling loads can cause serious injuries and even death.

Stand clear of suspended loads and do not step within their
swiveling range.

Never move loads without supervision.

Do not leave suspended loads unattended.

Wear suitable protective equipment.

 WARNING

Risk of injury from objects falling and being ejected!

Falling and ejected objects during operation can lead to serious
injury or death.

Take appropriate protective measures to secure the danger
zone.

 WARNING

Risk of injury due to unexpected movements!

If the power supply is switched on or residual energy remains in
the system, components can move unexpectedly and cause
serious injuries.

Before starting any work on the product: Switch off the power
supply and secure against restarting.

Make sure, that no residual energy remains in the system.

 WARNING

Risk of injury from crushing and impacts!

Serious injury could occur during the base jaw procedure and
when breaking or loosening the gripper fingers.

Wear suitable protective equipment.

Do not reach into the open mechanism or the movement area
of the product.

 WARNING

Risk of injury from sharp edges and corners!

Sharp edges and corners can cause cuts.

Use suitable protective equipment.

Summary of Contents for UFG 66





























Reviews: