• 4 •
3. FEATURES
1.
Battery clamps
2.
Micro-USB charging port
3.
Ready/Fail LED
4.
Battery status/Light button
5.
Battery status indicators
6.
Built-in work light
7.
ON/OFF Power switch
8.
USB port
9.
Air compressor ON/OFF switch
10.
Air compressor gauge
11.
Air compressor hose wrap cleats
12.
Air compressor hose
13.
Air compressor adapters and storage bag
14.
Micro/USB charging cable
1
2
3
4
5
6
7
8
11
9
13
12
14
10
4. CHARGING THE INTERNAL BATTERY OF THE JUMP STARTER
IMPORTANT:
CHARGE IMMEDIATELY AFTER PURCHASE, AFTER EACH USE AND EVERY 30 DAYS, TO KEEP THE JUMP STARTER’S INTERNAL BATTERY FULLY
CHARGED AND PROLONG BATTERY LIFE.
4.1
CHECKING THE LEVEL OF THE INTERNAL BATTERY
Press the
ON/OFF Power switch, and then press the
Battery Status/Light
button on the front of the unit. The LEDs will indicate the current charge level as follows:
Red LED flashing:
0-5% of full charge; immediately charge the unit.
Red LED solid:
6-49% of full charge.
Yellow LED solid:
50-75% of full charge.
Green LED solid:
76-100% of full charge.
4.2
CHARGING THE INTERNAL BATTERY
The jump starter will fully charge in 3-4 hours.
NOTE:
Use a 2A USB charger (not included), or a 2A USB charging port to quickly recharge the jump starter. Using a charger with less than 2A will increase charge time.
1.
Plug the Micro USB end of a charging cable into the input port. Next, plug the USB end of the charging cable into your charger’s USB port.
2.
Plug your charger into a live power source.
3.
When the unit is charging, the three LEDs will flash as follows:
Red LED flashing:
0-49%
Red LED solid and Yellow LED flashing:
50-75%
Red and Yellow LEDs solid and Green LED flashing:
76-99%
Green LED solid:
100%
4.
Ten seconds after the battery has reached full charge, the green LED will turn solid.
5.
If the Red
Ready/Fail
LED lights and the buzzer sounds, the unit’s protection has been activated (such as short circuit protection, battery low voltage protection, reverse
polarity protection, etc.) and the unit will not operate.
6.
When the battery is fully charged, disconnect your charger from the power source and then remove the charging cable from the charger and the unit. Make sure the
power switch is set to OFF, if not using the jump starter immediately.
5. OPERATING INSTRUCTIONS
5.1
JUMP STARTING A VEHICLE
IMPORTANT:
Using the jump starter without a battery installed in the vehicle will damage the vehicle’s electrical system.
1.
Turn the ignition OFF.
2.
Lay the DC cables away from any fan blades, belts, pulleys and other moving parts.
3.
For a negative-ground vehicle (as in most vehicles), connect the jump starter’s POSITIVE (RED) clamp to the POSITIVE (POS, P, +) battery post. Next, connect the
NEGATIVE (BLACK) clamp to the vehicle chassis or engine block, away from the battery.
4.
For a positive-ground vehicle, connect the jump starter’s NEGATIVE (BLACK) clamp to the NEGATIVE (NEG, N, -) battery post. Next, connect the POSITIVE (RED)
clamp to the vehicle chassis or engine block away from the battery.
5.
Press the ON/OFF switch to turn on the jump starter. The green
Ready
LED will light.
6.
It is best to wait 30 seconds after clamp connection to attempt to start the vehicle. Crank for up to 5 seconds. If engine does not start, wait 30 seconds before cranking again.
7.
After the engine starts, press the ON/OFF switch to turn the jump starter off, and then disconnect the black clamp (-) and the red clamp (+), in that order.
8.
Recharge the unit as soon as possible after each use.
5.2
USING THE USB PORT
The USB port provides up to 2.4A at 5V DC.
1.
Ensure the battery clamps are securely clipped on the storage holders.
2.
Flip the ON/OFF power switch to turn the unit ON.
3.
Plug your device into the USB port.
4.
Turn on the USB device.
5.
When finished using the USB port, flip the switch to the OFF position.
6.
Recharge the unit as soon as possible after each use.
