Schumacher ECLIPSE 5 Instruction Manual Download

Page: 18 / 30

www.racing-cars.com

TRACK SETTINGS

ROLL SPRINGS

See Page 6 - Step 5

Roll springs are used to control the cars steeing balance. A softer spring

will give an easier to drive car. Stiffer roll springs can be used to give a

more aggressive car. The standard setting has the roll springs

uncompressed and both just touching the lower pod plate when the car is

stationary. Screwing them downward and compressing the springs

creates more steering while loosening them gives an easier to drive car.

Adjusting the springs allows the tweak to be infinitely adjusted. Ensure

they are not set too unevenly. If more than 0.5mm different, further

investigation is required.

REAR BUMP SPRING

See Page 5 - Step 4b

This spring is used to set the pod angle of the car. Adjust the spring

tension so that the pod is horizontal when the car is on a flat surface.

A softer bump spring will give a more aggressive car entering the corner,

but offers more grip mid corner and on corner exit. It will also improve the

cars bump handling.

RIDE HEIGHT & CASTOR

- Increasing spacer ‘C’ increases ride height.

- Changing spacer ‘D’ doesn’t affect ride height.

- Increasing spacer ‘C’ or ‘D’ decreases droop.

Spacer C

Spacer D

(Kit)

*One Black King Pin Spacer = 0.25mm

Use the eccentrics to adjust the rear ride height. Raising the axle lowers

the ride height. Lowering the axle raises the ride height.

The recommended ride height is 3.5mm on carpet.

This is measured between the bottom of the chassis and the ground with

the car in running trim. First press the car down on to the ground and

release it once or twice to settle the suspension before adjusting the ride

height.

Ride Height

Spacer A

(Total)

Spacer B

(Total)

Rear

Front Ride Height & Castor Chart

See Page 7 - Step 6 & Page 8 - Step 8

Tyre Size

39.5mm

3.4mm

0.5mm
1.0mm
1.5mm
2.0mm
0.0mm
0.5mm
1.0mm
1.5mm
0.0mm
0.5mm
1.0mm
1.5mm

1.5mm
2.0mm
2.5mm
3.0mm
1.5mm
2.0mm
2.5mm
3.0mm
2.0mm
2.5mm
3.0mm
3.5mm

0.0mm
0.0mm
0.0mm
0.0mm
0.0mm
0.0mm
0.0mm
0.0mm
0.25mm
0.25mm
0.25mm
0.25mm

0.5mm
0.5mm
0.5mm
0.5mm
0.5mm
0.5mm
0.5mm
0.5mm
0.25mm
0.25mm
0.25mm
0.25mm

3º
3º
3º
3º
4º
4º
4º
4º
5º
5º
5º
5º

3.4mm
3.4mm
3.4mm
3.4mm
3.4mm
3.4mm
3.4mm
3.4mm
3.4mm
3.4mm
3.4mm

40.5mm
41.5mm
42.5mm
39.5mm
40.5mm
41.5mm
42.5mm
39.5mm
40.5mm
41.5mm
42.5mm

Ride Height

Castor

Spacer A

Spacer B

Spacer C*

Spacer D*

Summary of Contents for ECLIPSE 5































Search results

Summary of Contents for ECLIPSE 5

Reviews:

Related manuals for ECLIPSE 5

Brands by name

Popular brands

Schumacher ECLIPSE 5, Instruction Manual

Search results

Summary of Contents for ECLIPSE 5

Reviews:

Related manuals for ECLIPSE 5

Brands by name

Popular brands