background image

in ANSI standard #Z49.1. If ventilation is not adequate to exchange all fumes and gasses 
generated during the cutting process with fresh air, do not cut unless you and all bystanders 
are wearing air-supplied respirators. 

• 

Do not heat or cut metals coated with, or that contain, materials that produce toxic fumes 
(such as galvanized steel), unless the coating is removed. Make certain the area is well 
ventilated, and the operator and all bystanders are wearing air-supplied respirators. 

• 

Do not weld, cut, or heat lead, zinc, cadmium, mercury, beryllium, or similar metals without 
seeking professional advice and inspection of the ventilation of the welding area. These 
metals produce EXTREMELY TOXIC fumes that can cause discomfort, illness, and death. 

• 

Do not weld or cut in areas that are near chlorinated solvents. Vapors from chlorinated 
hydrocarbons, such as trichloroethylene and perchloroethylene, can be decomposed by the 
heat of an electric arc or its ultraviolet radiation. These actions can cause PHOSGENE, a 
HIGHLY TOXIC gas to form, along with other lung and eye-irritating gasses. Do not weld or 
cut where these solvent vapors can be drawn into the work area or where the ultraviolet 
radiation can penetrate to areas containing even very small amounts of these vapors. 

• 

Do not weld or cut in a confined area unless it is being ventilated or the operator (and anyone 
else in the area) is wearing an air-supplied respirator. 

• 

Stop cutting if you develop momentary eye, nose, or throat irritation as this indicates 
inadequate ventilation. Stop work and take necessary steps to improve ventilation in the  
area. Do not resume cutting if physical discomfort persists. 

COMPRESSED GASSES AND AIR EQUIPMENT HAZARDS 
WARNING 

IMPROPER HANDLING AND MAINTENANCE OF COMPRESSED GAS 
AND AIR CYLINDERS AND REGULATORS CAN RESULT IN SERIOUS 
INJURY OR DEATH!   To reduce risk of injury or death from compressed gas 
or air and equipment hazards, read understand and follow the following safety 
instructions. In addition, make certain that anyone else who uses this cutting 
equipment or a bystander in the cutting area understands and follows these 
safety instructions as well. 

• 

Do not use flammable gasses with plasma cutters. Only compressed air is suitable for plasma 
cutting. 

• 

Do not attempt to make regulator repairs. Send faulty regulators to manufacturer’s designated 
repair center for repair. 

• 

Do not attempt to lubricate a regulator. 

• 

Always immediately remove a faulty regulator from service, for repair, if any of the following 
conditions exist:  a.) Air leaks externally.  b. Delivery pressure continues to rise with down 
stream valve closed, c.)  The gauge pointer does not move off the stop pin when pressurized 
or fails to return to the stop pin after pressure is released. 

HOT SLAG/MOLTEN METAL HAZARDS 
WARNING 

PLASMA ARC CUTTING CAN CAUSE SERIOUS BURNS FROM HOT SLAG OR 
MOLTEN METAL!  To reduce risk of injury from serious burns caused by flying or 
dripping hot slag or molten metal, read understand and follow the following safety 
instructions. In addition, make certain that anyone else who uses this cutting equipment 
or a bystander in the cutting area understands and follows these safety instructions as 
well. 

• 

Wear leather welding gloves, a heavy long sleeve shirt, cuffless trousers, high topped shoes, 
a helmet and cap when cutting. As necessary, use additional protective clothing such as 
leather jacket or sleeves, fire resistant leggings, or apron. Hot slag or molten metal can lodge 
in rolled up sleeves, or trouser cuffs, and into pockets. Sleeves and collars should be kept 
buttoned and pockets eliminated from the shirt front. 

 

 

5

Summary of Contents for 120V

























Reviews: