Schulte FX-520 Operator'S Manual Download Page 105

Page: 105 / 166

OPERATION

FX-520 06/16

Operation Section 4-51

OPERA

ION

15. TROUBLESHOOTING GUIDE

TROUBLE

POSSIBLE CAUSE

POSSIBLE REMEDY

Excessive Vibrations

Check Gearbox bolts.

Tighten if loose.

Check for loose nuts on

Tighten if loose.

Blade holder and Blades
Check for bent output shaft.

Replace shaft if bent.

If shaft is bent oil will normally
leak from the bottom seal.
Check to see if blades are

Free blades so they swing

free swinging.
Check for even wear on each

Weigh blades. Weight should be

blade tip. Were both blades

within 1 oz. Always replace both
blades changed at the same time?

Blade Broken.

Replace blades, in sets.

Blade carrier bent.

Replace carrier.

Blade hub not properly

Remove hub, check tapered spline

seated on shaft

shaft, clean and replace.

New Blade or bolts matched

Replace blades or bolts in sets

Drivelines not phased correctly.

Replace Drivelines.

Implement & tractor yokes must
be in line.

Gearbox Overheating

Low on lubricant.

Fill to level plug.

Improper type lubricant.

Replace with NLGI 000 lubricant.

Excessive trash build-up

Remove trash.

around gear box
Bearing or gears set up improperly

Consult your dealer.

Gearbox Noisy

Rough gears.

Run in or change gears.

Worn bearing.

Replace bearing

Gear Box Leaking

Damaged oil seal

Replace Seal.

Bent shaft.

Replace oil seal and shaft.

Shaft rough in oil seal area.

Replace or repair shaft.

Oil seal installed wrong.

Replace seal.

Oil seal not sealing in the housing.

Replace seal or use a sealant

on OD of seal.
Oil level too high.

Drain oil to proper level.

Sand hole in casting.

Replace castings or gearbox.

Gasket damaged.

Replace gasket.

Bolts loose.

Tighten bolts.

Summary of Contents for FX-520







































































































































































Search results

Summary of Contents for FX-520

Reviews:

Brands by name

Popular brands

Schulte FX-520, Operator'S Manual

Search results

Summary of Contents for FX-520

Reviews:

Brands by name

Popular brands