Schonstedt Instrument TraceMaster Instruction Manual Download Page 14 | Manualshive

Page: 14 / 17

Schonstedt Instrument TraceMaster Instruction Manual Download Page 14

SECTION IV : BATTERY INSTALLATION

Receiver

The batteries for the receiver are located in the back of the LCD display head. There are eight (8) 'AA'
batteries. A battery access door with two thumbscrews is provided. Make sure the batteries are inserted
following the orientation illustrated inside the battery holder. After replacing the batteries secure the door
in place with the thumbscrews.

Transmitter

The batteries for the transmitter are in a battery holder located under the door at the bottom of the storage
compartment in the transmitter case. Slide both latches back and lift the door to expose the batteries. There
are eight (8) 'D' batteries. Make sure the batteries are inserted following the orientation illustrated inside
the battery holder.

NOTE: To remove batteries, slide the ejector handle to the right, this will lift batteries for easy removal.
For each of the four pairs, always insert the battery near the spring first.

«
...
12
13
14
15
16
...
»

Summary of Contents for TraceMaster


















Reviews:

No comments