manualshive.com logo in svg

Schonstedt Instrument MAC-51Bx, Instruction Manual, Page: 19 / 35

Share
Download
Schonstedt Instrument MAC-51Bx Instruction Manual Download Page 19

Inductive Signal Coupling (For HI Mode Only)

The most common method of applying a tracing signal is inductive coupling.  With the cover open and the arrow pointing
up, place the transmitter over the line as illustrated in Figure 4-4.  Turn the transmitter ON/OFF switch to ON and you
will hear a steady beeping sound.  If  not, replace the batteries.

Figure 4-4.  Transmitter Operating Positions

Conductive Signal Coupling (For HI and LO Modes)

If and exposed section of cable, line, or conduit is accessible, the tracing signal can be applied directly to the line.  (The
LF signal will not jump gaps.  So keep in mind that when applying the conductive signals to a metal pipe with non-
conductive joint gaskets, the LF signal only cannot be traced beyond the first joint from where the signal is applied.)

Plug the conductive cable assembly into the transmitter’s accessory jack and turn the power switch to ON.  (Inserting the
plug automatically disables the transmitter’s inductive mode and applies the exciting current to the cable clips.)  Connect
one cable clip to a conductive portion of the line.  Drive the ground stake into the soil off to the side of the line and
attach the other clip to the stake.  A good electrical contact between the clips, the line, and the ground stake is very
important.

Figure 4-5. Transmitter Hookup For Conductive Coupling

Schonstedt Instrument Company

4-3

WARNING

Clipping to power lines is dangerous and
should not be attempted.  Insulation on the clip
is not designed to protect against power line
voltages.

CLIP

ACCESSORY JACK

STAKE

CLIP

CABLE

Summary of Contents for MAC-51Bx




































Reviews:

No comments