manualshive.com logo in svg

Schonstedt Instrument GA-52Cx, Instruction Manual, Page: 9 / 17

Share
Download
Schonstedt Instrument GA-52Cx Instruction Manual Download Page 9

- 9 - 

Searching Areas along a Chain Link Fence 

 

Searching in the vicinity of a chain link fence requires a reduced sensitivity setting and some 

control over the orientation of the locator.  As illustrated in Figure 13, position the locator 

horizontally with its long axis perpendicular to the fence.  This ensures that the upper sensor is 

kept away from the fence. 

 

 

Figure 13:  Searching in the Vicinity of a Chain Link Fence 

 

Perform the search by slowly moving the locator forward along the fence while also moving it to 

the right and to the left.  As you move forward, this technique will allow you to search an area 

several feet wide.  Listen for an abrupt drop in the signal (as shown by the null in Figure 14) that 

will occur when the lower sensor, located 1-5/8 inches from the end of the locator, is directly 

over the stake.  Any variation in the position of the locator will produce an abrupt rise in the 

frequency of the signal. 

 

 

Figure 14:  Placement of Locator While Searching Along a Chain Link Fence 

 

Summary of Contents for GA-52Cx


















Reviews:

No comments