manualshive.com logo in svg

Schonstedt Instrument GA-52Cx, Instruction Manual, Page: 13 / 17

Share
Download
Schonstedt Instrument GA-52Cx Instruction Manual Download Page 13

- 13 - 

SECTION III:  MAINTENANCE 

 

The GA-52Cx is designed and built to give trouble-free operation.  Normally, maintenance is 

limited to the occasional replacement of batteries.  In the event that a malfunction does occur, 

refer to the Troubleshooting Guide.  The guide lists a few problems that can generally be 

corrected in the field so that you can continue using the locator without interruption. 

 

Replacement of Batteries 

 

The GA-52Cx is powered by two alkaline 9-Volt batteries.  Alkaline or lithium batteries may be 

used; however, lithium batteries are recommended (due to their exceptional performance).  

Lithium battery manufacturers advertise a 10 year shelf life (two to four times the operational 

life of an alkaline battery), and they advertise being environmentally safe.  If battery leakage 

does occur, lithium batteries do not cause as severe of damage to the unit as alkaline batteries 

would. 

 

As illustrated in Figure 18, the batteries are carried in the battery holder. Access to the batteries 

is obtained by removing the two knurled nuts and sliding off the cover.  Always replace both 

batteries. 

 

NOTE:  When replacing the batteries hold the instrument by the metal chassis to avoid any 

contact with the printed circuit board and its components. 

 

 

Figure 18:  Exploded View of the Electronics Unit Cover 

 

 

Summary of Contents for GA-52Cx


















Reviews:

No comments